Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Hello Team,
We are currently working with the nRF54L05 and using the nRF Connect SDK. We have successfully evaluated basic BLE peripheral samples on the EVK.
For our application...
Hi,
I am going theough the first lesson of 'nRF Connect SDK Introduction' course, have installed nrfutil and updated the path. When trying to install 'device' as per the...
Hi, I have this problem and I couldn't find any working solutions. I am developing my own hardware and there weren't any problems until I started to use debugger. My program...
Is there any reference information on how long (in ms) different steps in a BLE pairing process takes? e.g. Pairing Feature Exchange, Short Term Key Generation, Long Term...
Hi all, In my project i'm using the nrf52840 SoC in my board. I'm currently working on the bootloader, and I would like to add additional logic to functions mentiond in the...
Hi,
I am trying to train a few beginner FW engineers on RTOS concepts and have been using the Nordic training videos. However, sometimes, its tough to explain thread execution...
Hello,
I need to persist ~200K of data on the internal flash of an NRF52832 chip. I've run a memory report and I'm current taking up 185Kb and the chip has 512 Kb of flash...
Our project has been working on nRF21540 & nRF52833.
Let us have a method to reduce the power of nRF21540 under 400uA at idle.
Currently, without nRF21540, the power...
We started a new project using nRF Connect SDK & Zephyr. Installation of development tools is very easy and convenient using VSC add-ons. However, we are concerned about the...
Hi, we have a project where we want to track the location of a Thingy91 and send it to an nRF9160, a cellphone or/and a website. Do anyone know about any guides that could...
During a ble connection process using a nrf54l15 as a peripheral, I get an sdc fault "File 48, Line 203" with this callstack:
sym_476LRB5XNUARAHCHHC7ZAIGPFC5VZ4W2N4467LI...
Hi,
I'm building an application for the nrf5340 in rust and I want to be able to use the bluetooth LE audio functionality. For this I have two questions:
How can I build...
Hey,
I get the following errors when running my application and I am not sure how to debug this (The nrf thread viewer is empty when I start a debug session of my application...
I try to use one 5340 board as cis client to connect with Galaxy Buds2 Pro and can get the audio in headset.
But the connection is randomly disconnected, the log i get is...
"When I run the CDC ACM example to enable UART, it works fine. However, when I switch to another example that also uses the same USB configuration, the USB port is not visible...
