Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi Team,
I am currently working on the nRF52805 module and have developed an application that supports dynamic service creation (runtime GATT service creation).
During...
Hi folks, so I will start by saying I have had this device working at home under Windows 11. I have brought the device to work to use on my works computer, which is still...
Below is the relevant code and log:
SDK：v2.9.1
static void dfu_work_handler ( struct k_work * work )
{
int ret = bootmode_set ( BOOT_MODE_TYPE_BOOTLOADER );
LOG_INF...
Como faço para habilitar o registro de logs do mcuboot para visualizar os logs de atualização DFU no nRF Connect SDK 2.9.2, usando o nRF54L15 em uma placa personalizada com...
Hello team,
I attempted to measure the sleep current on the nRF54L15 DK board, but I’m seeing a very high current draw of about 74 mA.
I built and compiled the peripheral_power_profiling...
Hello,
We are developing a custom board that uses the nRF54L15 chip, and are trying to flash an application along with MCUBoot to allow for OTA updates. When I flash the...
Hi Nordic folks,
I'm trying to get the nrf54L15 in a Fanstel BM15M to go into the system OFF state and be woken up later by a timer. All the documentation I've seen says...
What's minimum hold time for a pin reset on nRF54L10? https://docs-be.nordicsemi.com/bundle/ps_nrf54L15/page/pdf/nRF54L15_nRF54L10_nRF54L05_Datasheet_v1.0.pdf doesn't state...
Hello, I am developing an application that uses Bluetooth Channel Sounding, and for that reason I need to have two devkits connected to my computer at the same time, but the...
Hi there,
I was designing an add-on development board to go onto the development kit to test a 1.8V application. I need VDD:nRF on the 54LM20 to be set as the same as VDD...
I connected the new nPM2100 EK to Linux PC and opened the nPM Power UP application. In the app I'm able to select the EK. The nPM Power UP tells me that " Programming required...
I have an NPM1300 demo board. After testing, the default voltage of VOUT1 is 1.74 V. If I use this voltage to power the VDD of nRF54L15, will it affect the power-on reset...
Hi Nordic
We plan to use 54l15+7002e, how much storage will spend for nRF7002 up layer stack and application(e.g typical Wi-Fi STA with TCP client connections)?
What I've tried:
Testing Summary: SD Card on Port 2
Setup : Wired an SDHC card (Transcend 8GB) to the Connector P2 (middle header) on an nRF54L15 DK v1.0.0...
In my code, I find I can start up the ble pakage sending. but it alway send out without stop. I need send out one package. and stop. In my radio callback. I do call this task...
