I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
What version of LVGL is used with nRFConnect for VSC 2.7? Where can I find this information generally. It seems like the lvgl version is 8.3, but I don't know why I think...
Hello,
I am writing this thread to ask what would be the hardware configuration for the QKAA version of the nRF5340 chip if I don't want to use the wireless features of...
I am considering using the nRF7002 for a Wi-Fi application. I want to use an nRF54L15 as the host for an nRF7002 and operate it using Target Wake Time (TWT) to periodically...
I need to connect to other units according to their MAC address. I'm assuming that this:
BT_SCAN_FILTER_TYPE_ADDR
Is the thing to use in this:
bt_scan_filter_add...
Hi, I am working on a project where I need to add ble dfu as well as serial dfu issue I am getting on adding serial dfu to ble example I am getting error variables undeclared...
Hi,
My ultimate goal is to add NDT [1] to a meshtastic [2] device implemented with RAK4631[3]. For this goal I can see the following obstacles:
- The meshtastic stack...
Hi,
I am trying to modify the ble_app_blinky example in such a way that I can connect with multiple central devices to on peripheral device.
So far I found a good start...
From "nrf_section.h" (__GNUC__):
Example for the section name " log_const_data ":
NRF_SECTION_DEF(log_const_data, nrf_log_module_const_data_t) //: extern nrf_log_module_const_data_t...
I am using NCS Connect SDK version 2.6.0
I am trying to create an array of models and found a problem with using Zephry macros in C++ projects. My main.cpp is as below ...
I have a sample app (hellow world from the zephyr samples).
It compiled well on my system in vscode using 2.7.0 and sysbuild.
I then installed 2.8.0 and suddenly the build...
Hi,
I just got nRF54L15 Development Kit boards. I installed 2.8.0 nRF Connect SDK and toolchain into VS Code. I was using 2.6.1 versions,
with nRF52840 and nRF5340 DK...
Am making a project based on NUS central demo and I can connect to our remote unit with the 52840DK, I can send data over a UART into it and I can get data out which is received...
Hi Community,
I made a custom board based on thingy53, created a similar custom board file folder.
The application code can be compiled correctly with the original thingy53...
I am using NRF Connect for VS Code on Ubuntu 24.02 with an adafruit nrf52840 feather express. When attempting to use the DeviceTree Extension, the wrong dts file is listed...
