I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
We are using the npm1300 with a battery with an NTC.
Can we add a ferrite between battery NTC and npm1300 NTC?
Note: there is an error in our design we will...
I have managed to get, somehow, a central_uart talking to a peripheral_uart on a pair of 52840 DKs.
I've changed the UUIDs of what I'm trying to connect to, to be those...
Hello!
I built the https sample app for the Sparkfun_I got run time errors.
my setup:
Updated Windows 11 Pro
SDK 2.6.1 and 2.8.0
How do I solve this?
"The Modem...
Hi,
I am using a Proteus-e module from Wurth Elektronik for a project. This module contains a nRF52805 chip. I am using the nRF Connect app to send commands to configure...
Hello.
I'm trying to enable MCUBOOT in my project.
I added CONFIG_BOOTLOADER_MCUBOOT=y to the prj.conf, but I'm getting the next message: " BOOTLOADER_MCUBOOT set more...
Dear Nordic, We wonder if it is possible to connect to the BLE side of nRf9160dk using the LTE BLE Gateway sample. https://docs.nordicsemi.com/bundle/ncs-2.3.0/page/nrf/samples...
Dear:
I am useing NCSv2.6.0 version.On the basis of my project, adding RTT printing of Bluetooth scan packet and scan response packet will frequently appear Log crash. ...
Hi!
I have built a sample application "location," got some warnings, and got runtime errors. I have attached a zip file with code and images.
I just have reinstalled...
Hello,
I would like to add a costom cluster,controlled by custom App.I add cluster xml file,and run zap_regen_all.py to generate corresponding code.Everything is ok, the...
I am testing the current consumption of SIM cards with PPK2.
When PPK2 is connected to VCC ( voltage 1.8 v or 3 v ), the PPK2 can display the current properly ( around 9...
Hello I need to read the current mesh IV index of a provisioned node. Found 2 structures with the iv_index field : struct bt_mesh_cdb bt_mesh_cdb and struct bt_mesh_net bt_mesh...
When I package the firmware with nrfutil v7.12.0 version， I pack with a command like this
I got the right app.zip，manifest file
My question is: In nrfutilV7.12.0,...
I am planning to perform encryption using the CC312 accelerator on the nRF5340. I would like to evaluate the power consumption when using the accelerator.
My approach is...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
I clone the project from git and try to build the project using custom board but it is giving the cmake error...
