Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello,
I have a question regarding a recent issue.
I'm currently developing with the nRF52840 IC or EVM, and I'm facing a problem. Whenever I write firmware to the flash...
Hi Team,
I recently purchased 2 Audio DK's and I set one up as a gateway and the second as a left headset. I was able to pair the two, stream audio from my PC through the...
Hi,
We are currently developing a BLE device (HW and SW) using the NRF52811.
As we want to be able to update the device via FOTA we need to have the Bootloader to have...
Hello,
I am trying to upgrade my project from ncs 2.1.0 to ncs 2.6.1. I am running into some strange issues with mbedtls and I suspect it's because the same ciphers enabled...
Hi All,
We're going through BQB certificate with our mice, and we're informed that test get failed because new rule will be implemented in May 2023.
Our Chip is NRF52833...
Hello,
I want to use external flash. I did some research on the subject. I am using SDK 2.6.1. I have a few questions.
1- Does the spi_flash example I examined work on...
I have a custom nRF9160 board running a modified asset_tracker program. I am using UART0 as a command line interface for testing and debugging. I can enter commands to setup...
Hello. I'm trying to do spi communication on a custom board with nrf5340 used. I'm using three threads, I build it, but if I put it on the board, the board will have a problem...
Hello I’m using the NINA-B306-00B BLE module which uses the nRF52840 MCU for a custom board application. The BLE module interacts with two sensors, an accelerometer via SPI...
Hello, I get a compiler warning when I try to log a float value using the LOG_INF macro in my project. The code I'm using is from the cell-fund course: lesson 6, ex. 1. Toolchain...
HI,
I have a function testfun from a customer-provided .a library, and I hope to run this testfun function in RAM. I am currently using NCS 2.8 based on the nRF52840. I...
Hi, I read others cases obout the problem to send more than 20 bytes trhough BLE and add on my prj.conf the next three lines:
This is the entire prj.conf:
Butr when...
NCS 2.7.0
NRF52840 DK
I am trying to trigger an advertising sent callback to indicate advertising timeout or a maximum number of events. I have tried increasing the workqueue...
Im using nrf5340 with nrf connect SDK 2.6.
Im trying to follow this post to evaluate hardware timer for reading saadc
But I constantly am getting
CONFIG_NRFX_TIMER1...
Hi,
I have successfully built and ran the MQTT sample ( /opt/nordic/ncs/v2.7.0/nrf/samples/net/mqtt) on the nRF9160-DK. I did have a few problems with SIM coverage and firmware...
