Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I'm working on developing a desktop app, which can communicate with nrf52840-dongle or any Nordic device. I'm using UWP to develop the app. I'm new to App development so i...
Hi,
I'm evaluating the nRF9160-DK with the SOFTSIM feature enabled.
I would like to know if there is a way to tell the softsim to wait for APDU response for more than...
Hi, I have a BLE application where I want to use the device firmware updates (DFU) over Bluetooth. I followed the nRF Connect SDK Intermediate tutorial on how to enable the...
Hello!
I'm using the nRF5340 for a school design project and as such am financially limited to relatively low cost board manufacturers.
It seems that most of these manufacturers...
Greetings,
I'm trying to add an existing folder from a project with its' contents, but it seems that it only adds files that are included in the folders, the other nested...
Hello,
I am currently working with the Nordic nRF9160DK and am using the https_client example from the examples in the nRF Connect via VS Code (on Windows OS), and as far...
Hi,
I have been trying for months now and don't seem to find a way to build a signed app for mcuboot without having to build the whole mcuboot itself.
In the board files...
hi,
I am using nrf9160+NCS v2.6.1. When the CONFIG_SHELL_BACKEND_RTT feature is enabled, the power consumption increases by 80uA. After investigation, I found that the default...
Hi
Built and flashed ncs2.7.0 SLM application at NRF9151 DK. It will log booting log messages and then "Ready" as below.
Before ncs2.7.0, I found SLM application only...
Dear All.
Using, for instance, a peripheral nRF52840 SoC, would it be possible to change in real-time the text string being advertised, among several prerecorded ones, according...
Hi,
I am following the tutorial to implement the serial recovery on nrf52840DK https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-8-bootloaders...
Hello,
Im using SDK 15 ble pheripheral and central uart example on my custom nrf52832 board.
I would like to know how to set MIN_CONN_INTERVAL and MAX_CONN_INTERVAL for...
Hello,
I would like to send a reason code when disconnecting the client (nRF9160DK) and server in MQTT. How can I do this?
It seems that there is no argument to specify...
When I use nrf_dfu_mbr_copy_bl to do bootloader updating, the data is copied sucessfully, but I find some flash data are updated from 0xFE000 and 0xFF000：
The data is the...
