Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I have problem with program nrf21540 UICR EFUSE. The first time, WR-UICR was able to successfully write, and after reset the reading of reg0 displayed correctly. But...
My setup includes 2 nRF52840 DKs, one flashed with periodic_adv_rsp and the other with periodic_sync_rsp. I copied the samples and auto-generated a build configuration for...
I cannot get Zephyr-only DFU over BLE working. Using an NRF52840DK. This is my prj.conf :
---
CONFIG_GPIO=y CONFIG_LOG=y # CONFIG_BOARD_HAS_NRF5_BOOTLOADER=n # Enable...
I am working on nrf5340dk board with 2.6.1 SDK and toolchains.
So, I took "mesh_shell" project as a starting point, then added external flash and mcuboot with simultaneous...
I would like to prepare my RAK4631 supported board file to Zephyr , but I am having problems with my JLink device, then I bought a new device but it didn´t arrive yet.
...
Hello,
i am using the nPM1300 with a nRF52840. This question is regaring the WDT in the nPM1300.
After reading the datasheet of the nPM1300 my understanding is, that event...
i have ZSWatch complete hardware by jackob and kempy and the link is provided below and using the vscode (nrf connect) to code in it in my case the debugger by segger technology...
am using the NRF52840 DK to interact with some BLE devices, and I am trying to use NRF Connect for Desktop Bluetooth Low Energy .
While the DK is correctly recognized in...
I'm, trying to use the ble_app_uart example for SDK v17.1. I can run the example correctly, but when I try to copy-paste the main code, I can't use the UART. I normally send...
Hello Support,
I was trying to get the information of services and characteristics from the peripheral after the connection is established.
With sd_ble_gattc_primary_services_discover...
Hello,
Is there a method of setting the transmit power of ISO channels using BT_HCI_OP_VS_WRITE_TX_POWER_LEVEL?
I used the connection handle of the struct bt_conn object...
Hello,
I want to use SPIS peripheral in nrf7002-DK on the net core. I cannot compile (error 'NRFX_SPIS0_INST_IDX' undeclared (first use in this function))
here is my firmware...
Hello Nordic Team,
I'm struggling with a bug on HID transfert.
My product send HID buffers with a size of 32 bytes, everything was working fine so far.
But when I...
I already did a new VSCode/nRF Connect for VSCode Extension Pack installation, but I can´t find what kind part is missed in the instalation process
In the Build and Flash...
