Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
With the NRF_CLOUD_MULTI_SERVICE sample, we'd like to set the GNSS location tracking sample interval to 2s or even 1s.
But we found that the actual time will be about 25s...
Hello everyone, I need to attach a QSPI memory to an NRF54L15 module. I am led to believe that this should be supported out of the box but cannot understand how to use the...
Hello everyone,
I am working on a project where I need maximum range and TX power, since my Bluetooth device will be implanted the signal is strongly attenuated I need maximum...
Hi,
We are evaluating the NRF9151 for live tracking purposes. While testing with the nRF9151-DK we noticed the we had tracking fallouts using AT#XGPS=1,1,1 both during driving...
Hi everyone,
After the latest update of the nRF Connect SDK plugin for VS Code (2025.4.106), we've seen this pop-up appear. We are using v1.8.0 and now we are not able to...
Assume the nRF21540 used as a front end for nRF52840. When the nRF21540 module is in power down mode can it pass the signal without significant loss? If yes what is insertion...
Hello,
I've searched a good amount of online content, but I cannot publicly find a good enough reference design for the nrf52840-DK, natively compatible with Kicad.
...
Now I can use LIBUARTE to receive data from MCU, but have a trouble: it can't receive a whole packet sometime,and return it with 2 parts.
UARTE : 115200/8/1
receive buffer...
Hi Support Team
I installed the NCS V3.1.0 just now. But there was an issue of west: unknown command "build" for the NCS V3.1.0 when I built a sample. Many thanks.
Hi,
I'd like to raise this issue I am having with the v3.0.1 sdk wherein the final build stages I get the message attached
I am using the Lesson 9 exercise 5 sample...
I am trying both v3.0.0 and v3.0.2 SDK; the board I am using is the nRF9160DK, version 1.1.0. There are 4 scenarios:
1) Run on Linux (minicom or Serial Terminal) following...
Hi Support Team
Our product have a CD 4kv and AD 8kv ESD test, but the samples reset on AD 8kv close to the USB, the reset register show it is nRESET PIN reset.
add an...
I'm having several problems with the Intermediate course, L2_e2. In Step 3 it says that there is 'a bug in coredump_gdbserver.py that causes a crash if building with optimized...
I need to use a nrfx timer in order for some GPIO timing, but can't get past the simple examples declaring an instance. For testing I'm just using the 54L15DK.
I was using...
