I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I got some Holyiot "YJ-17017-USB" dongles, which use the nRF52832. From my Windows dev environment, I want to load firmware on them (SoftDevice, etc.), but I'm not sure how...
I have an NRF52 DK, and an IM21 door sensor that advertises events. I am trying to pick up these events with the nRF52DK in the most robust way possible. I have used the scanning...
Hello Experts,
When I use a X-Ray machine to check appearance of NRF52840 . But I found out that there were some abnormal phenomen as same as a photo below:
Any body...
I'm developing a beacon-like product using an nrf52840 with S140 on CR2032 battery. In PS under sleep current draw, it list 0.97uA for system ON, RAM retention OFF. I'm trying...
Hi, I have developed a BLE/ZigBee application starting from nRF5 SDK for Thread and Zigbee v3.2.0. Now I need to add a "timer" for measurement timing most precise as possible...
Hello all. Is there a possibility to implement a "software watchdog" on the nRF51822 SoC. I would like to react with this watchdog not on external events (e.g. hardware-actions...
Program received signal SIGTRAP, Trace/breakpoint trap. HardFault_Handler () at ../../../../HAL/NRF52/HAL.cpp:122 122 __debugbreak(); (gdb) bt #0 HardFault_Handler () at ...
Hi,
I've added usb function to nRF52840 project accroding to usb sample projects.
The function was all right but the device manager showed the the 52840 as "USB serial...
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
The timer is called for every...
I have a Fanstel BT832X evaluation board (model EV-BT840(832)-V4). Nordic examples without softdevice are working fine. Examples with softdevice are not working. I have checked...
I’m getting some strange behavior after repurposing the WS2812 driver sample with the following code. Note that my code has Bluetooth enabled. It seems like it might be some...
I use ncs1.6.0 to develop on nRF52832DK. The current requirement is to enable PA LNA support on mesh.
I learned how to use FEM driver through this blog . I added the corresponding...
Hello,
Is it okay to supply the nRF21540 with a DC/DC or do I need to use an LDO? Are there any performance differences of the nRF21540 when choosing one over the other...
I'm finding that the signal strength of the radio is too low in my nRF52840 custom BLE project. I would like to increase the radio power from the default 0dB as our RSSI values...
