I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am trying to use a remaining timer/counter in the nrf52832 as a divide by 64 counter to get rid of an off board MC74HC4060 counter chip we are using for I2S from an external...
Hi Nordic Semiconductor!
Over the years I've been using your development kits, some days ago I got the nRF5340-DK and started on a new computer. Normally I dive into the...
I don't know why, but after issuing the nrfutil dfu command line, it takes ~34 seconds before the DFU starts and the progress bar is shown.
Sample command lines:
nrfutil...
Hello,
I want to use a FIFO. I want to send the data from file1.c and receive it on file2.c.
Currently, I have defiend my_fifo using K_FIFO_DEFINE(my_fifo) and using...
I am currently working on AoA direction finding solutons, and I have successfully run the demo direction_finding_connectionless_rx and direction_finding_connectionless_tx...
Hello,
I would like to ask you if there is an antenna layout available for the nRF52833. Indeed, I would like to develop my own application with it and, this SoC needs to...
Hello all,
I am currently working on receiving SAADC data and transmitting it through BLE with a sampling frequency of 1kHZ or higher. I am using nRF52832 board with the...
Hello, I have custom BLE service and characteristic as below image.
I wanted to discover them in ble central mode. I have modified ble_hrc_c.c to validate but central...
dear all
When I use QSPI to operate external flash and mount a FatFs file system, when I use RC = FS_ open(&file, fname, FS_ O_ CREATE | FS_ O_ WRITE); When creating a file...
Hello DevZone,
For my project I have a number of pins generating interrupts from different sensors.
I've read that GPIOTE IN events consume a bit more current than the...
nrf_mesh_config_app.h at the generic level mesh example contains constants like DEVICE_COMPANY_ID, DEVICE_PRODUCT_ID and DEVICE_VERSION_ID . I've expected those values to...
I try to build your an example Smart Remote 3 nRF52 v1.2 in Keil v5.34 and I have some errors.
In the case of nRF52832_xxAA (Target: PCA63519-SR3_nRF52832_Shield) I have...
Hi,
I'm a beginner trying to understand BLE extended advertising. I have modified the peripheral/ble_app_beacon example to broadcast extended advertising packets with PHY...
