I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I am transmiting extended advertising packets and I want to set the flags on the extended header as specified on the bluetooth core specification (v5.3) page 2691 (photo...
I am following the Getting Started directions here: https://www.nordicsemi.com/Products/Development-hardware/nrf52-dk/getting-started#infotabs
Steps 6 and 7 do not work...
I am currently using the power profiler kit ll to see if it is suitable to run power consumption tests in our automatic test system. I am using the python API from https:...
Dear community,
I'm using BM833A chips which contains a nRF52811 nordic chipset. I use a S140 softdevice, for both, beacon sender and central.
I have configured both to...
Dear Sirs,
SDK: NCS version 1.6.0
Board: nrf5340 DK
IDE: SES Nordic Edition V5.50c
Compiled in application core cpuappns
I am a beginner with nrf programming...
Hi all,
we use nRF Connect for Desktop Programmer tool for flashing nRF5340 at production plant. Our Regulatory Affairs & Quality Assurance dept. is asking for a validation...
Sometimes the Power Profiler App does not display the average current and charge values for the Window (see screen capture, below). The values are displayed while the capture...
I'm working on a program using the ble_peripheral/ble_aapp_uart project. While testing the program, it was confirmed that the connection was disconnected after 1 minute 35...
Hi ,
I tried to use the sample code of central and peripheral project "ble_app_hrs_rscs_relay" , to add a new service to connect with light and button peripheral by "lbs_c_init...
Hello,
we are developing a PCB with a nRF52840 in normal power mode. I know that VDD and VDDH have to be shorted in the normal power mode, but due to a layout error we have...
when debugging peripheral_uart sample in ncs1.5.0 used nrf5340dk board , a error produced in function static int bt_init(void)
static int bt_init(void) { int err;
err...
I am trying to use nrfjprog.exe (for the first time) to see if my code is being corrupted on a power fail. It keeps returning an error that I can find documentation on.
...
Hi,
We bought smart watch from company xyz. Watch is running using Nrf52840 and supports buttonless DFU. we are customizing the smart watch firmware as per our requirements...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
My device is a peripheral. I want to connect with two smartphones. At that time, I want to connect under the following...
