Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
How to check CS procudure used by controller in BLE Channel sounding security I am refering to this ticket so i have questions related to it that
I have tried to find answers...
I have three 5340 Audio DKs (PCA10121) and I am trying to demonstrate one as the broadcaster and the other two as headsets with audio transferred between them but NRFconnect...
Hello,
I’m working with the nRF5340-DK using nRF Connect SDK v3.0 and the SoftDevice Controller. My goal is to support multiple simultaneous connections , and I have already...
The Errata 155 workaround seems to work for the nRF52840, but only when events are configured before tasks. If I configure a task for an unused output pin *before* configuring...
Hello, I want to use the nRF52820 as a slave device. I've left my code, prj.conf, and DTS files below, but the spi_transceive function seems to be getting stuck. What could...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
nRF54L15 LE Audio with I2S interface, LC3 codec point-to-point audio The specific flow is as follows: The nRF54L15 communicates with the mic via I2S to capture audio data...
I'm facing a persistent issue with my nRF9151-SMA-DK kit when trying to perform USB debugging, uploading, recovering, or erasing.
Interestingly, other boards (nRF9151-SMA...
Hello, we use nrf52832-ciaa in our project and it is light sensitive. Could we use x-ray to inspect soldering quality or it will damage the mcu? Thank you, Anton
I tried to find an explicit statement whether a new IMEI needs to be written to nRF9151.
These sources state that nRF91x1 ships without IMEI and it needs to be written:...
We are working with Nordic’s official peripheral_esl ( https://github.com/NordicPlayground/nrf-esl-bluetooth/tree/main/samples/peripheral_esl ) sample application for Electronic...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hi,
We are working on a project using the nRF5340 Audio DK. We want to take user input either from UART or BLE, and switch between them based on the connection status. ...
I would like to know the approximate flash memory footprint required to implement BLE Mesh, Zigbee, and Thread , individually. Could you please provide the details for each...
