Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Dear Devzoners,
I have a question about triggering received data via UART with the nrf_libuarte_drv .
Prehistory: We started using the libuarte async driver, but due to...
nRF5232 consuming too much power with BLE advertising interval 2 secs. I had tried using MbedOS6/OS5 and as well sleep_mode: deep sleep. Can anyone help, my appplication is...
Hello,
I have been trying to follow tutorial from:
https://devzone.nordicsemi.com/nordic/short-range-guides/b/mesh-networks/posts/thread-tutorial-practical-guide-for-device...
Hello,
through figuring out how AWS FOTA works and following the instructions of this page
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/nrf9160...
I found a couple of threads that the Windows version of the Power Profiler App in nrfConnect is broken, which it is also for me. It used to work in the past and I also like...
Hello there,
During my development I have discovered an issue with app_timer library. It is fragile for calling stop/start functions from interrupts which has higher priority...
Hi,
I have a project with nrf52832 without any BLE operation. Software runs with FreeRTOS. I am trying to add ble dfu into this project. There is a button connected to the...
Hi,
I am using nrf52832 development board with sdk 17.0.2 and softdevice 132.
I have freertos project which had ble nus service and aes cbc logic added to it.
I have...
I am trying to run the ble_app_uart from the ble_peripheral folder in the NRF SDK 15_2 I am testing with a Nordic 52840 DK (PC10040). I have made essentially no changes. ...
Hi, Nordic staff.
I'm working with Central device using S132.
There is a peripheral device using S112 in Nordic. I didn't make this peripheral.
My question is...
Hello all.
I have a question relate to: How to "ble_app_hids_keyboard" app can connect multi device?
My task: make equip peripheral base on nrf52811/840 can Adv and connect...
Hello, I am new to Nordic, I was previously using Cypress CYBT343026-01. But there were some drawbacks found during development. 1. It was consuming 315μA at 0 dBm BLE tx...
Perusing the GCC linker script supplied as part of SDK v16, I noticed that the .data section is specified as follows:
.data : AT (__etext) { __data_start__ = .; *(vtable...
I now need to burn the app firmware and modem firmware of multiple 9160 chips at the same time. Using pynrfjprog to write a program to burn the firmware for ten chips(Open...
