Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
We are trying to synchronize time across 3 nrf5340, where one will be master and the other 2 nrf5340 will have to synchronize their time with the master.
1. All...
I had raised ticket " https://devzone.nordicsemi.com/f/nordic-q-a/63754/nordic-sdk-qspi-driver-call" .
Wanted help for using qspi driver with non blocking mode. I have modified...
Hello, does anyone tried terminated vs unterminated RF switch in AoA / AoD application? According to forum, some people use terminated switch, some don't.
Also, there should...
I've a prototype board which I need to externally program. The prototype board supplies it's own 3v supply to the chip (working fine) via a 5v supply which is current limited...
Hi,
I am using NRF52832 with SDK 17.0.0.
I wanna try to connect multiple devices with only one Android phone.
When I try demo on Samsung galaxy S8, I can connect with...
I am using SDK 14.01 and ble_app_beacon example in that, I want to send updated sensor data in advertising. Using ble_advdata_set() I am able to send the updated data in advertising...
SDK14.0+NRF52832: firstly I init the passkey in the function gap_params_init as above.I want to change the passkey and can save the new passkey to flash, but when I input...
Dear all, I want to measure the current consumption of my application on a nRF52833 DK. On top of that I want to be able to power the device using the VDDH and set the VDD...
Hello,
I am trying to run the A-GPS sample program but am encountering a bit of difficulty with the SUPL code.
I had to modify the LTE connection code to allow access...
Hello,
I am using nRF51422 DK running on SDK v12.3.0. I am migrating the project examples/ble_central/ble_app_uart project from Keil uVision to Segger Embedded Studio using...
Hi,
I am trying to toggle one pin via PPI when receiving event on another pin - code snippet below:
#include <stdbool.h> #include <stdint.h> #include "nrf.h" #include...
Hi,
What is the fast way to stream data from NRF52840
1) Using USB interface and virtual com (CDC)
2) Using UART interface and extenal converter as DTFI
Please Advise...
Hi,
I use SDK16 and S140 softdevice v7.0.1. I try to send a binary file from mobile to nRF52840 (PCA10056). I download examples\ble_peripheral\experimental\ble_app_ots project...
Hey Guys,
I am trying to send a mesh message to a group address using nRFMesh application in IoS. After accessing the Groups tab, it is showing as "No models configured...
