Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I have been using nRF9160: LTE Sensor Gateway to send data from nRF52832 to the cloud. The nRF9160 is subscribed to nRF52832 and hence gets updates after every certain period...
Hi,
I'm trying to use Power Profiler Kit (PPK) with nRF52 DK to measure the power consumption of our custom hardware. My setup is as described below: - The PPK is connected...
SDK:15.2
IC:NRF52840
Hi，When I upgraded the device using usb dfu, after entering the app, there will be an additional current of about 180uA（Sometimes appear）.
Both...
Somehow my nRF9160 DK board has become essentially unresponsive. Flashing new modem using nRF Connect Programmer, and downloaded nRF FW, "seem" to work. But nothing else....
The asset_tracker repo now has a file called: prj_nrf9160_pca20035ns.conf
Is this still compatible with the nRF9160 DK that is using pca10090n ?
What does the pcsNNNNNn...
Hello everyone,
im using the nRF52840 DK, softdevice s140 and the ble_app_tamplate example. In this example i can send data through the GATT protocol. But i want to change...
Hi ,
I would like to know if the .dat file inside the DFU packet is always the same or it can be different.
Is it Possible to fix inside the code ?
What is the .dat...
Hi all
We are using nRF9160 DK & want to test its MQTT library by uploading some data to the broker. But, my city doesn't have LTE Cat-M1 / NB-IoT network.
Can you suggest...
Hi,
1. ZigBee Cluster Library Specification(Rev 6) -> 3.3.2.2.3 Battery Information Attribute Set -> Table 3-18. Attributes of the Battery Information Attribute Set tell...
Hi,
I am a beginner to nrf9160.
I already can do send the large data to server. (Maybe not too large just about 15KB)
In my test, I will send that data in every 25 minutes...
Hi,
I am not able generate dfu_package.zip using nrfutil.
I am using ubuntu 18.04, and python2.7 is installed is default python version.
I get the following error when...
Hi!
I have bought the Thingy:91 and in user guide (on page 12) it says that the nRF91 DK should be used to update the modem firmware, further more, it seems like it is only...
Hi I am trying to program the bsp buttons on the NRF52 DK, so pushing button 1 will toggle start advertising and going to sleep by calling sd_app_evt_wait().
I have successfully...
