I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi, I'm developing a project on nRF52832 with LIS3DH accelerometer . Is there anyone here who has already done a similar project using the nordic SPI bus (not TWI)? Please...
Hello NordicSemi,
Actually we want to develop a product that can communicate with the iPhone over USB (lightening connector).
Basically want to implement iAP2 protocol...
Hello,
While i am debugging application in SES.I got the error like "stopped by vector catch"
How it relates to hardfault handler .Why it is happening
Kindly provide...
Hello everyone at Nordic!
The QFP version of the nRF52 has a reference PCB design layout, which is shown on the eval board. For example, if you look at the schematic for...
Hi,
I am using Segger Jlink with SWD interface
nrfjprog used to work perfectly fine for me but, suddenly, I cannot run any nrfjprog commands, I get the error JLinkARM...
I am trying to use nrfx_timer and nrf_drv_ppi in Light switch server demo example. But I face undefined reference error.
I have add c files path and include in CMakeLists...
I waas working with nrf52840dk sdk15.3.0 and pca10056 now I would like to migrate my code to nrf52840 dongle with pca10059 aht changes should I do ?
and how can I debug...
I'm writing my own BLE discovery routine for S140. I'm finding that after I call sd_ble_gattc_descriptors_discover(), BLE_GATTC_EVT_DESC_DISC_RSP is passing attributes that...
Hi,
I just wanted to report that there is an issue with the solution suggested in this thread . Even when you manually manage double buffers outside the ble_advertising...
Dear all, I started nRF52840 development. Using this module, I'm going to use BLE and USB connection.
I have nRF52832 module, which sends BLE data by 1.28Mbps. I'm going...
Hello all,
if we design a AoA receiver based on the nRF52811 and our own antenna array, will it be able to locate beacons using Bluetooth 5.0 communication?
Kind regards...
We intend to connect an A-D converter to GPIO lines in SPI mode. The ADC generates a done pulse that is positive 3.3V and 56ns to 64ns wide.
Looking at v1.1 datasheet...
Hello,
During application development I've got SoftDevice fault PC: 0x000251BA. It happens always just after start `FDS Garbage Collector`, so I expect that can be related...
Hello. I work with two board nRF52832. One of them is a server, which has rx/tx characteristic, the second acts as a client. In both projects used BLE NUS.
When client NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Good morning
I have designed master slave cards with nrfl2401, I have to certify them (CE) I need a declaration of conformity.
In your site I found nothing I would have...
