I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello, I'm using softdevice 6.0 and SDK 15.
In my application, I would like stop the SAADC at the disconnection and then restart SAADC at the connection to power saving...
hi..........
i am using nrf42840 ...segger 15.2 version
i am facing the problem in sleep mode
i used the command to sleep
static void power_manage( void ) { ret_code_t...
Hi guys,
I am currently using nrf51822 with SDK 11. I use Peer Manage to deal with paring and bonding encryption in BLE connection.
Please correct me if I am wrong but...
Hi,
When I'm trying the throughput on nRF52840 with SDK v14.2, I set up a 52840PDK as a 'repeater'; in which case the 'repeater' will receive the output (20kBytes in total...
which app should I use when I want to do LL BQB test with harmony on nRF52840?
it can not connected with harmony when I use DTM project. It seems the interface of nRF52840...
Dear nordic,
I am currently working with nRf52840. For designing antenna is there any role for dielectric layer thickness and conductive copper layer thickness
Hi all, I'm testing quick connections and communications using multilink(nus). I am using multilink central example in nrf52832(Central : softdevice v2.0.0 & SDK v11, Peripheral...
I am trying to measure the power consumption when transmitting data from an external device to nRF 52832 to a smartphone.
I am trying to measure the power consumption of...
Dear, I'm designing a PCB with nRF52832 and I will intend to use DCDC converter therefore I putted the two inductors (10uH and 15nH) between DCC and DEC4 pins. The same hardware...
Hi,
I am developing a project in IAR Embedded Workbench for nRF52840-Preview-DK. I have integrated different modules (ble, ADC, SPI, I2C) in this project. I don't have...
I like to integrate the nRF54XXX with a LNA/PA combo (skyworks RFX2401C or 66110). Could you please tell me which pin should be used to control the RFX2401C TX/RX? Which has...
Hello all,
I am currently working on a project to control a door lock and use ble_app_multirole_lesc as reference.
As measurement the current consumption is around 6.5mA...
Hi, I’m working on low power wireless sensor network. I have a big dilemma in choose of wireless mesh solution. Maybe firstly, what i need: 1. Support for low power devices...