Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
The code assumes that check_rollovers_and_update_eid(...) is called every second, and that m_security_slot [slot_no] .timing increases monotonically with 1. If this is not...
Hi
I have tried to run DFU example from SDK 15.0.0_a53641a.
I also use nRF Connect v2.5.0 to update firmware.
I flashed Soft device and secure_bootloader( examples/dfu...
I'm trying to enable the UART module. The function calls follow:
nrf_init -> nrf_drv_uart_init -> nrfx_uart_init
Here we see that nrfx_uart_init() is called with
result...
I suspect I could avoid writing (admittedly, simple) code to map ble service objects to connection handles and vice-versa if I knew how to properly use the BLE Link Context...
Hi, I am merging the Thingy app (Segger with softdevice s132_nrf52_4.0.5) with the UART example (taken from ble_app_uart in SDK 11). I have been fixing some errors before...
Hi All,
I built a custom board that mounts a nrf52840 chip and I followed the schematic N 5 of the datasheet.
I also have 2 evaluation boards nrf52840 EVB "PCA10056",...
Hello,
I am interested to know if the device nRF51824 compliance with the ATEX zone norm (for example, working in certain parts of the chemical industry)
Best regards
Windows7 , nRF5_SDK_15.0.0_a53641a-ble_app_uart,,
Environment setting of SEGGER embedded studio for ARM V 3.34a
I am preparing to develop ble_app_uart using [SEGGER Embedded...
I create a mesh use Mesh SDK v1.0.1 and there is just a group ,and I want to create more groups. I compared it with Mesh SDKv2.0.1 which divide servers into two groups . The...
SDK14.0 , s132_nrf52_5.0.0_softdevice, computer platform: windows 7
//----------------------------------------------------------------------------------
I use one motor...
Hello,
I am developing a beacon using the long range feature of BT5. In order to do so, I added the line m_adv_params.primary_phy = BLE_GAP_PHY_CODED in advertising_init...
Hi,
As well know, user need to modify sdk_config.h to match different used case.
Would you please tell me the easier method tools to modify the content of " sdk_config...
Hi,
I am new to NRF development. I am using 2 nrf52840 DK one as central and other as peripheral(for reference). I am using ble_gap_gatts example from central side. i...
Hello,
I am using NRF52840 development board with SDK 15.2. I am using the template peripheral project since i want to get comfortable with the peripherals on the board...
Hi All,
I am working on customized board using nRF52840 chip, I have a application which was developed using nRF development kit that communicates to my customize board...
