Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi engineers,
I posted a question at the link below, but it doesn’t seem to have received a response yet. If it’s convenient, could you please help answer the question?...
I'm debugging the function of switching between ESB and BLE. My general approach is as follows:
Initially, the BLE protocol stack is initialized, advertising starts...
Hello.
I'm looking for some advice debugging what I think is a race condition around bt_le_per_adv_sync_delete.
After calling bt_le_per_adv_sync_delete, we're sometimes...
Hi,
I am trying to use CoAP Block Transfer to transfer firmware images from server to nRF5340 custom board. We are using OpenThread library for CoAP.
The block transfer...
Hi,
For my university masters group project I need to connect my nRF5340 Audio DK to another board (Ambiq Apollo 510B). I will need to send audio from the mic to the Apollo...
Hi Nordic team, I’m working with nRF54H20DK on nRF Connect SDK v3.2.2 and using MCUboot as the bootloader. From the current documentation and samples, my understanding is...
Hello,
I'm trying the bootlader of SDK13.1, with SD S132_nrf52_4.0.2
I manage to send a ZIP file to the bootloader, but the application doesn't launch. I've tested with...
I'm developing BLE code using the s140 + Nordic 52833 with nrf5 SDK. My flash contains the hex files for s140, the bootloader, and the app. I've encountered a strange issue...
Hello,
I am a junior developer currently working with the nRF52840. I have been developing and debugging successfully using the nRF52840 Evaluation Kit (DK) without any...
Hello, In the latest nRF Connect SDK 3.2. , I've been having a few "sysbuild/mcuboot/boards" folder layout issues with nRF54L15DK / nRF5340DK when using external device FLASH...
SDK v3.0.2 Toolchain 3.01
I'm beating my head against the wall for what should be a trivial matter. I need to use P2 for uart: RX is P2.00 TX is P2.02. No RTS CTS in use...
Hi
When running a project on the nRF54L15 using nRF Connect in VS Code, I often cannot connect to RTT. I select RTT in nRF Connect, but no output appears. If I retry multiple...
Hello,
I am able to reproduce this issue in a blank project where CONFIG_I2C=y and CONFIG_I2C_SHELL=y (and dependencies) are configured on an nRF54L15.
When I use P1...
On the device we're developing (small battery powered sensor tag, Thread Sleepy End Device usinc NCS v2.7.0), when trying to discover DNS services using the `otDnsClientBrowse...
