Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
Hi All,
Hardware: Custom Board (Buttonless)
SDK : 17.0.2
SD: 7.2.0
Support required: DFU Buttonless
We are able to successfully load and run the DFU buttonless...
I am using nRF52832.
Can I use NFC1/P0.09 as SCL and NFC2/P0.10 as SDA?
nRF52832_PS_v1.4.pdf states "The pin capacitance will be higher on these pins" in 4.3.2.
I am...
I posted one question in my earlier ticket about download firmware to our own device (nRF9160) through DK of NRF9160.
Now we are design the schematic of our own device with...
Dear Concern,
I am getting MCUboot build errors as shown in the below.
C:\Nordic\v1.5.0>west build -b nrf5340dk_nrf5340_cpuapp -d build_mcuboot bootloader/mcuboot...
Hi,
I have nrF52840 DK rev 2.0.1
switch to VDD, Default, SB40 is cut (confirmed by multimeter)
I have the PPK rev 1.1.1
switch DUT to DK
switch Power to DK
I...
Hi,
is possible use for DFU process as DFU server other device as development kit?
I will use it in street lighting but it not usable with development kit. I would use...
I have a couple of examples that work ok on 9160-dk and use SPI3.
However, if I try to use these on SPI1 or SPI2 I get a device not found error.
I am building with west...
hi,
i am working on timer example in peripheral folder. i am including this example in ble_uart example in ble_peripheral folder. i am getting error " 'NRFX_TIMER0_INST_IDX...
I am using the SHT21 sensor for measuring temperature and humidity, trying to connect it to nRF52840 DK Board using TWI mode.
I am unable to even scan and get the response...
I deleted the flash completely for the bootloader example, then I installed soft device. The softdevice area for nrf52832 is written as 148 kb in the documents. In nrfgo studio...
hi,
i am using working on example "pin_change_int" in peripheral folder.in this example interrupt occurs when there is state change on interrupt pin. how to enable interrupt...
Hi,
Is it possible to upgrade a S112 v6.1.1 softdevice to the S113 v7.2.0 softdevice using BLE DFU?
I am getting the following error right after the SD + BL has been...
Hi folks,
I am playing around with the A-GPS sample.
I am trying to send the fix every five seconds to the cloud. This should be possible according to the webinar last...
