Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
We are planning to use the DFU SDK to update the firmware from an Android tablet(central) to multiple peripherals/slaves at the same time. The FW is around 200KB and...
Dear Nordic team,
I am using a NRF52832 and SDK15.3 + SD6.1.1 and Segger Embedded Studio to develop my code.
I started developing my code from the example "ble_app_template_pca10040_s132...
Hello,
I'm trying to use an oscilloscope to profile my current consumption on the nRF9160DK. I'm setting up according to the spec here: https://infocenter.nordicsemi.com...
I am now using SDK1.3.0-rc1 with NRF9160. I use the serial_lte_modem project and using nrf52 to send at command for controlling nrf9160.
I can connect to the network,...
Hi every body, I am using nrF9160 SDK. I am testing the sample project Blink_LED. In the documentation is written that LED1 is connected to P0.02. If so then why the voltage...
Hi, I would like to measure the elapsed time difference between using FPU and not using FPU in my app (nRF52840). I'm thinking to use the FPU FFT as the base example. So I...
Hi all,
I'm working on a custom Bootloader for my nrf52840-based board. The bootloader needs to support DFU from external SPI Flash. So far, my bootloader can read from...
I am working on the Thingy_SES_FW project ses file provided here . I have the goal of compiling this file. However when compiling errors(shown below) core_cm4.h: No such file...
Is there a notification signal that the ZBOSS provides that will let the coordinator (ZC) know if a router (ZR) that was in the network no longer present?
For an example...
Hi, I have been trying to get Thingy91 to work with the LwM2M sample found here . It works fine with the nrf9160 devkit and it seems to work for ~1min or so with the thingy91...
Hi,
I am using NRF52832 with NRF SDK 15 and Mesh SDK 4.0.
As my knowledge, I can update firmware for my device using SDK15. I want this cause my network does not have...
Hello,
As specified in the subject, I would like to know if there's a way to verify that a peer is already bonded with my device. My goal is to verify if a device is bonded...
hai ,
in my application i m using ble_app_multilink_central example for connecting with multiple peripherals.
how to connect with multiple connections ??
tried with...
Hi,
I would like to use the nRF52840 DK as a BLE Sniffer.
I followed nRF Sniffer for Bluetooth LE v3.0.0 User Guide but cannot run the DK as what is expected.
I...
Hi,
there are some erratas from the BT SIG mentioned in
https://www.bluetooth.com/specifications/errata/
Are they fixed/handled in softdevice S132 6.1.1 or any other...
