Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi,
I'm trying upload firmware onto the nRF24LU1+ dongle (nrf2728) from the nrfgo motherboard (nrf6310) through nrfgo studios. I have it hooked up just as described in the...
Hi,
With my mistake, the firmware in nrf52840 Dongle is none, Do you know how to get the official firmware? and how to download this firmware? if using Jlink, any pin support...
Hi All,
I have a scanner project based on nrf52840 + S140 and I saw S140 (7.0.0) seems to support nrf52811.
So I want to port existing project to nrf52811 + S140 7.0.0...
Hi, I am experiencing the nrf52832 with some testing and developing few examples.
I am using nrf5_SDK_15.3 SES. OS : Windows 10.
I am using nRF52832 only. I have seen...
When designing an NFC coil to use with the nRF32832, are there any recommendations as to the coil inductance and Q that we should target?
Being a passive design, we are...
Hi I am using the tutorial from https://github.com/bjornspockeli/custom_ble_service_example . I have uncommented some of the starter code from ble_cus.c. My understanding...
I am inquiring about something I know very little about but will try to communicate for the information. Smart phone applications can be opened through a QR code which utilizes...
Hi,
We are using ncs tag v1.0.0.
I am using i2c_scanner example firmware. It works find when used as it is.
When I added "UART2" in this firmware i am getting hard fault...
Using the ble_app_uart example, Using oscilloscope to measure the time interval of broadcasting, two development boards are used respectively. One development board is nrf51422...
Hello, rols and hkn:
I got two different answer about watchdog and hardfault in devzone.
1. watchdog can't reset hardfault. https://devzone.nordicsemi.com/f/nordic-q-a...
https://github.com/bjornspockeli/custom_ble_service_example
I am currently following this example with SES on my NRF52840 DK (PCA10056). I copied the ble_app_template example...
Are there any recommended alternatives (& nordic plugins) to the discontinued Bluetooth Developer Studio? I'm looking for a tool to make the process of creating custom GATT...
Hi! I want to copy data from internal flash to a statically allocated buffer in RAM. I get a DACCVIOL hard fault try to do this by memcpy. The hard fault depends on the number...
I need to send 5 sensor values received over SPI to an app over BLE about 5 times a second. I also need to send a few configuration parameters from the app back to the nrf52...
