Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
As part of our evaluation on the Nordic BLE SOC, I want to measure the throughput, range and the power consumption.
Can someone point me to any sample program(s) that I...
A while ago I was experimenting with the usbd_msc demo, trying to get the firmware working as RAM-disk-only storage, without any permanent storage like Flash or SDC. While...
Dear Team,
We need a SoC which can support the following features for our wearable product.
1) Battery Charging
2) I2C interface for sensor
3) GPS
4) BLE
Regards...
Hi, I have run light switch example in SDK 15.2 and SDK for Mesh version 3.1.0, when I try to add new app_onoff_server_t model to Server with my code:
and I have modified...
Hello,
i noticed that even i send AT%XMODEMTRACE=0 with response "OK" the bsd lib triggers EGU0 / Trace interrupts. The modem is not started, but the bsd lib got succesfully...
We are using a Raytac MDBT42Q (nRF52832) Bluetooth in one of our products.
We are using nRF Toolbox for Android/IOS for testing. Is there any Windows 10 nRF Toolbox??
...
hi guys, I'm confused about bluetooth 5. Is there some example that use it? i have a nrf52840 board and i will like to use it in order to send my data but i didn't find any...
HI
I am trying to develop a mesh network using nordic mesh SDK..where nrf52 dongles will be beacons for which beaconing example will be used and from SDK
52840 DK will...
I startet evaluation with nRF52840 and SES.
I found the BSP Demo to crash (HardFault in Debug) after app_timer_init() , because of a NRF_LOG_INFO() inside, but Logging not...
Hi Sir,
As the title, can 51824 support BT 4.2 in Zephyr? Any document (or link) descript this?
If yes, which SDK version we can use?
Thank you.
BRs, Han
Hello,
I am working on nRF9160dk. I want to send gps coordinates via sms using nRF9160dk. Last week, I tried simple_at program to send sms and it worked. Now I am working...
When I am receiving data from slave data is missing. Means if o am reading 255 bytes then 127 bytes are right after that I am receiving alternate bytes. Some times I am receiving...
Hi,
I was wondering if anyone has sample code that would support a 16 x 2 LCD over an I1C interface.
Something like this.
https://www.amazon.co.uk/HALJIA-Character-Backlight...
hi,
in the SDK15.3，I successfully ported the DFU demo to app_uart, but the 52830 will enter the upgrade state each time after downloading the program. I want to know how...
