Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I am developing a system that will read from a sensor that uses I2C and then transmit this to a "master" using ANT+ or BTLE (this isn't decided yet)
For the prototyping...
Hello,
Where can I find the pre-built binaries for the below Provisioning options :
1.OOB (Public Key) and Authentication - Input
2.OOB (Public Key) and Authentication...
Hello.
I have an nRF51822 chip and I'm trying to figure out how the whole nRF5 sdk works.
I am using the Segger Embedded Studio.
I downloaded the last nRF5 SDK v15.3...
Hi!
I'm trying to use the AWS-FOTA sample, I flashed the sample onto the board and it connected to the AWS account successfully, but when I try to add the update.bin file...
Hi. The main loop of my app is mostly doing SPI communication to a GPS receiver. I'd like it to do that every second or so and spend the rest of the time in system on but...
Is it possible to configure the ACL to protect the UICR registers?
If so, would this have any impact on the SoftDevice or other nRF52840 peripherals? I.E does the SoftDevice...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
Hi
I am a beginner in the MCU and SoC realm. I was checking the nRF52810 WLCSP33 specs but could not find any mention of the bluetooth range. Is it a standard range for...
Is anyone aware of the status of NBIoT / CATM1 use on flights? Are they covered by the various "mobile phone" limitations of use?
I'm referring to the use of a product containing...
Hi,
I am developing central device application which shall run on Win7 PC + nRF52840 dongle / equivalent nRF52840 DK
I intend to develop in C# / C++ and call PC-BLE-driver...
Hi all,
I have a problem with ble_app_beacon example. I'm using sdk v15.2 and my board is this . The problem is that I can see the beacon alive in the nRF Connect app on...
Hi Devzone, I am struggling to build projects in SES. I am getting "fatal errors" when I try to build applications and samples. See following output from SES (asset_tracker...
Hello,
I tried using the Thingy:91 out-of-the-box, but didn't succeed, using a SIM (LTE-M/NB-IoT) of a local operator. I suppose this is possible?
Thanks.
Guy
Does Nordic provide a BLE functionality with a USB dongle that a PC application can use? I do NOT want to use the Windows 10 BLE as it is buggy and does not provide the low...
