Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hello,
I am using nrf51822 and supply is provided through rechargeable battery. Please review my schematic and suggest changes if there is any.
Thanks,
Shailav
I used the following code to verify the working of the clock (at P04) of nRF24le1.
I used a 4.7K pull up resistor with a VDD of 3.3V, which was output from the nRF.
Note...
Hello,
I'm using nrf51822/s130/sdk12.1.0.
Before adding BLE code there's no problem in writing inner flash.
In main I just added below ble_app_uart codes(not modified...
Hi,
I have Wireshark version 1.10.14 and sniffer version 1.0.1. I send the data out from PCA10040 with connection interval of 7.5 ms and packet throughput of 200Hz using...
The pulldown on the SAADC is 160k. Is it ok to create a resistor ladder by adding an external resistor of, say, 400k, enable the internal pulldown and then input a higher...
Hi NordicSemiconductor's community,
I have a basic question about connection to a BLE peripheral.
I use the SDK_10.0.0 and s110_v8.0.0.
I want to know how to implement...
how to change RX and TX operations ?
i wrote next code:
#include "nrf_esb.h"
#include <stdbool.h>
#include <stdint.h>
#include "sdk_common.h"
#include "nrf.h"
#include...
Hello
I used one example from the nrf52 SDK and wanted to add another functionality to the code. How do I know what to add to that file?
Is there a global sdk_config.h containing...
I am migrating from SDK 12.2 to SDK 13 on Nrf52.
I use Eclipse.
I have a few questions:
In SDK12.2, there was :
Patch for SDK 12 - implements required workaround...
i am using nrf52832 dk. i am trying to change the flash address from 0x000 to 0x0002000. But i can only flash it to 0x0002000 if softdevice is already present on controller...
Hello,
I want to clarify one thing related to the limitaion in SoftDevice S130 V.1 of L2CAP_MTU size by 23 bytes. Is any way to extended it?
Because I see that changes...
Hi All,
We are trying to flash our custom NRF52832 board using NRF52-DK+nrf studio. With the same setup that's suggested by devzone.nordicsemi.com/.../
However, from...
