I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi all,
I'm a grad student trying to innovate on the BLE concept. I require a continuous signal as a source: preferably unmodulated, but a long duty cycle could also work...
The NRF52 product specification (aka, datasheet) has 3 chapters in it all relating to TWI: TWI (chapter 49), TWIM (chapter 33), and TWIS (chapter 34).
Which section (TWI...
Hi,
I'm trying to interface SIM808 with nrf51822 over uart using nrf_drv_uart. Everything works well for some time, but then uart starts reporting error code 1, NRF_UART_ERROR_PARITY_MASK...
Hello,
I am working with the GPIOTE library to get a GPIOTE_IRQ from a peripheral.
I have several questions regarding the library and how IRQ works.
1.How do I clear...
Hello,
I am using SDK7.1.0 for NRF51822.
In my subroutine, I would like to disconnect with the peer device, and re-advertise. But when after re-advertising, I found the...
Is it possible to set scope for search in info-center only for SDK 11? It search in all SDK versions and sorts results randomly. It is very annoying. Especially when there...
Hi,
I want to build expertise in BLE and want to use the Nordic nRF51x22 to build a hardware and write the firmware for the same.
I am planning to use the nRF51 DK....
I'm calling sd_ble_gatts_characteristic_add multiple times to add characteristics to a peripheral. At some point I get a return value of 0x200020B6. I'm not making much headway...
Hello everyone,
I am trying to use the ble_app_hrs_rscs_relay example from SDK V11 for s130 (2.0.1).
It compiles and works well when I use an pc10028 evaluation board...
If I have multiple services, 2 for example, how should I set up the srdata.uuids_complete.p_uuids in the code:
ble_advdata_t srdata;
memset(&srdata, 0, sizeof(srdata)...
Hello,
I am developing beacon on nRF51DK and I want to store in non volatile memory some parameteres like:
ProximityUUID
Minor
Majnor
AdvInterval
Tx_power...
Is it possible to configure SPI Master API to send multi-byte words?
My peripheral expects transfers in 16-bit blocks (CS goes low, 16 bits are clocked in, CS goes high...
Hi guys,
I'm going to start the development of a new project based on nrf52832 and I have to decide the firmware architecture and APIs. Designing the support for the Nordic...
I am using a digital microphone using i2S interface with the following signals: BCLK (bit clock), WS (word strobe), SELECT (select for Left/Right) and SDOUT (digital data...
I received that error using master control panel version 3.7.1
While using the last nRFgo Studio (1.21.2) it tells me JLinkARM.dll is not correctly installed. Please run...
