Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
I will use ADC / Button function over SoftDevice.
below by source.
the thread is repeated not go beyond the conn_params_init.
#define ADC_SAMPLING_INTERVAL APP_TIMER_TICKS...
Hello,
I am working on s130 softdevice(SDK 6.1.0.0 and nRf51822 &nRf51 DK). I have one peripheral and two centrals. but the data from peripheral should be read from only...
I find this function.
tx
void ble_send(uint8_t * data, uint8_t length)
{
ble_nus_send_string(&m_nus, data,length);
}
ble_send(&data_array[0],10);
but I don...
Hi, I'm trying to run ESB during the timeslot api requested slots.
The problem is that BLE uses app_timer, which uses SWI0 for the callbacks, and at the same time, ESB also...
Hey , I am working on nordic nRF51822 chip and using it as an iBeacon. I want to send some custom data apart from UUID,major,minor in the packet. How can I send it ?
As in...
When I try to set a breakpoint in eclipse by clicking on a line, gdb tells me in the eclipse "Console" window below the code: "No symbol table is loaded. Use the "file" command...
Hello,
I have three custom services. I wanted to add descriptions to the characteristics for easier testing and debug, so I used the typical method to add descriptions...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi
I'm trying to test UART over BLE using the nRF51-DK and the sample code "ble_app_uart_s110_pca10028 (nRF51 PCA10028)" along with both the nRF UART APP for both Android...
I'm using nRF51822 SoC , is it possible to change the major value when i push the button ? I tried simple assignment but it didn't work so i ask if i have to use the function...
hi,
i have kept RAM block 0 and RAM block 1 on in OFF mode by calling "sd_power_ramon_set(0xf000f)" before entering off mode ,i saw the value of RAMON register is 0x00030003...
I'm using nRF51822 SoC . I wanna read and write from the flash memory . Shall I use a specific configuration before using read and write functions provided from S110 softDevice...
we have created ble mesh, and data through ble nodes is passed every 5 seconds, but nodes gets disconnected with reason BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED??
please someone...
