i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
I tried to find an explicit statement whether a new IMEI needs to be written to nRF9151.
These sources state that nRF91x1 ships without IMEI and it needs to be written:...
Hello, I have a project based on nRF9160 and nRFCloud (CoAP), and uses a SIM from 1NCE. This SIM allows to connect to 3 different MNO at my location in France (Orange, Bouygues...
By default the GRTC peripheral is not cleared when started via sys_clock_driver_init . This is because nrfx_grtc_init calls nrfy_grtc_prepare , however NRFX_GRTC_CONFIG_CLEAR_AT_INIT...
Hi I want to know if I can use the nRF52850-DK to flash the Xiao Sense Plus from seeed? I am following the following tutorial which says I need to use a J-Link but that's...
Nordic published a great blog in 2022: "Comparing range with Bluetooth Low Energy of the nRF21540 DK and the nRF52840 DK." It clearly explains the range capabilities of the...
I am new to Zephyr RTOS . i have a breakout board of Max32664D from protocentral interfaced to nrf52840 development kit . i want to get started with this sensor hub max32664...
What is the default transmit power of the nrf5340 when performing an AoA test in connected mode? How do I change its transmit power to perform AoA accuracy tests at different...
Hi,
I tried to change security level, but it's not changing.
When i set CONFIG_BT_SMP_SC_ONLY =y, it's working well with security level 4,
but i want to change mode1...
Hello everyone,
I am a beginner looking to dive into the world of HID (Human Interface Device) development, specifically using the NRF52840 microcontroller. I recently...
One of our products that's been in the market for a couple years is a bit behind on the NCS version (v1.4.2). I am currently doing the 18031 RED Cybersecurity documentation...
Hi Nordic Team,
I'm currently working on a BLE project using NCS v2.9 and targeting a custom board based on the nRF54L15. My goal is to use the SYNTH LFCLK source (instead...
Hello,
I am a beginner when working with nRF. I am trying to run the l4_e3 solution code, but it doesn't seem to work. I can connect via BLE, but nothing is being shown...
I have problem with i2c that can't read the cst816s, its always return log message `<err> cst816s: failed reading chip id` and `<err> cst816s: Could not read x data` when...
Hi,
I am working on zigbee demo "light_switch" with NCS2.8 Add-on SDK.I enabled MCUboot according to the steps in the course " Lesson 9 – Bootloaders and DFU/FOTA "
1...
