I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello:
I have questions about eSIM card.
As we know, GSMA standard eSIM card is an empty chip, we can use eSIM card after ISP information is installed into eSIM card....
Hello,
I have the same question as mentioned in this article:
https://devzone.nordicsemi.com/f/nordic-q-a/19252/how-to-avoid-interrupt-handling-is-not-missed-with-sd_app_evt_wait...
Hi,
I use nrf sniffer to monitor BLE communication. After pairing with encryption, wireshark indicates Encrypted packet decrypted incorrectly (bad MIC).
I think there...
I configured Uart on 23 - Rx and 24 - Tx of NRF52832.
In simple uart example it works fine with uart_event_handle for rx.
But when this code is merged with Nrf Mesh Dimmer...
Hi,
Having gone through the nRF52832 datasheet, the only discernible drawbacks of moving from an external crystal to synthesizing the Low frequency clock from the high-frequency...
On the Nordic Semiconductor infocenter , 12 reference designs for the nRF52840 are given, 6 for the big QIAA chip and 6 for the small CKAA chip. However the reference designs...
Hi
We are developing the use of ESB together with BLE, using the Timeslot API.
We have been using the known tutorial for the ESB timeslot implementation:
https://devzone...
Hi,
We are using nRF52832(lairdBL652) module for indoor application for the prototype version.
We are using nrf52832 for both central and Beacon device.
We have made...
Hi,
I have combined the light switch and the dimming example. The thingy 52 contains one generic onoff server and two generic level server for brightness and colour.
The...
I updated Thingy91 with modem firmware (mfwnrf9160100.zip) and application firmware (thingy91_ltem_v0.2.2.hex) from latest firmware package (thingy91fwv022.zip).
Question...
Hi,
I have nRF9160 DK. I downloaded nRFConnect SDK with source code.
I know that samples compiled with libraries are loaded and executed under MCU on the DK board. Since...
I only want to dfu for bootloader ,but i have some problem ( insufficient resource、 dfu success but my device is crash ).
maybe my bootloader.zip flie is error.
can you...
Hi guys,
I am using mesh server example with UART fuctions integrated into it.
I wanted to send a string through UART.
I tried using app_uart_put() function and this...
Hello,
I was wondering when a device needs to be certified and if that is a country by country basis? If you were to follow the circuit guide lines, would you still need...
Hi, I am using https://github.com/NordicSemiconductor/pc-nrfutil code from here for nrfutil. I am working on both mesh and standard ble application.h I am facing problem keeping...
