Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
After a successful LESC bonding, the address given by p_ble_evt->evt.gap_evt.params.connected.peer_addr in a BLE_GAP_EVT_CONNECTED event is a "identity address" as expected...
Hi,
I've been trying to figure out how to configure a nRF52832 device using SDK 15.2 and S132 to act as both a central and peripheral device for a relay device. In looking...
Hi,
We have a custom device that has 15 buttons. Presently we use the following code to initialize and use the button interrupts. I am using a __WFE(); to wait for the next...
I got this project to compile and work: https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master/samples/nrf9160/gps
I have the latest radio firmware at this time...
Hi Sir or Madam
nRF52832 support ANT+ function using 2.4G ISM frequency, but i am not sure the frequency list and channels number/ frequency bandwidth, is there any software...
Hi,
i am trying to interface ultrasonic sensor with nrf9160, but i dont get any examples regarding ultrasonic. so i tried the interrupt method to measure the time of gpio...
nRF52832 Product Specification v1.4 states:
11.3 Writing to user information configuration registers (UICR)
User information configuration registers (UICR...
Hello Nordic team,
I'm currently looking into TLS on nRF52840, I'm using nRF SDK 15.3.0.
I have seend the DTLS example "nRF5v15.3.0\examples\iot\dtls\coap_client" that...
Hello Nordic experts,
I am doing SDK 15.3.0 usbd_hid_composite example and this is where I am: https://devzone.nordicsemi.com/f/nordic-q-a/50447/nrf52840-usbd_hid_composite...
My firmware goes into system off state when idle and wakes on GPIO (button input). I want to display an indication to the user for a fixed duration, so I will modify the bootloader...
Hi,
I'm using nRF51822 chip and SDK 12.3.0 library to develop the software. We want to control the motors with PWM. But since PWM consumes a lot of power, we decided to...
Hello.
For My personal project , i would like to develop a buttonless OTA DFU on my Red Bear Nano V2 (Based on nRF52832 SoC Chip) . Im using the SDK11 and i have folloawed...
I'm trying to add RTT support into the secure BLE bootloader to get debug logs, but after adding the files it's consuming too much flash:
Is there any way to fit RTT support...
