I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I am able to program the device with switch and light examples and controlling light device through switch device also done for mesh communication.
How to control...
Hello,
I am using nRF52832 on SES v4.12 with SDK v15.3 and SD v6.1.1 on a custom board.
Background:
I want to perform OTA DFU and with that i have two services enabled...
Hello:
Is it possible to configure the nRF52840 for Standard Serial over Bluetooth? The application I am developing for needs a long range Bluetooth connection, where...
Hello, I am developing an application that requires the device to keep track of time with the RTC. I am using an app timer driven by the RTC to provide me with a 1 second...
Hi,
I have download the nRF5_SDK and try to run the example code. But I can't understand the relationship between PCA10056 and nRF52840 chips.
If I run the example project...
Hi
I would like to connect a BME680 sensor to the nRF9160DK board. The driver for this sensor isn't included included in the v1.14.99-ncs2 branch but it shows up in the...
Hi,
I want to directly enable notify without discovering the service handle, but it didn't work(return NRF_ERROR_BUSY). Because it takes time to discover the service, and...
Hi, As we know that, we can see, the data has been sent to nRF Cloud in JSON format by Thingy91-PCA20035. And we can also see that, we have respective APIs like "cloud_send...
Hey,
I am getting a
warning: #47-D: incompatible redefinition of macro "STATIC_ASSERT_SIMPLE" (declared at line 215) warning: #47-D: incompatible redefinition of macro...
Hello, I am working on a ble application which is streaming data via ble notifications. I am currently queuing up the packets in the notification queue and keeping track of...
Hello,
I am trying to use as least energy as possible. I run the ble_app_blinky example. The only change I did was commenting out: advertising_start(); such that no advertising...
Hello,
I'm using the nRF52840 Development Kit and SDK16.0.0_98a08e2.
I'm trying to run the example "proprietary_rf\esb_ptx\pca10056\".
It compiles and runs if I do not...
Hi,
I am not getting the exact starting and ending address of user flash storage like other controllers, How we can find that while using FDS and Fstorage and also i want...
I have a custom board with 5 buttons, and a status LED, using the nrf52832_xxaa chip. 2 of the 5 buttons never trigger an interrupt. It seems like this is because nrf_gpio_pin_read...
