Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hello, I do connection between one nRF52840 (central / NUS) to multiples nRF52840 (peripheral NUS)
in my function static void on_adv_report(nrf_ble_scan_t const * const...
Hi Nordic Developers,
I would like to extend my question on creating vendor specific model from this question I posted earlier (extension of Thingy Mesh Demo v0.1):
https...
Hello Nordic Pros,
Doing some debugging using RTT Viewer and an nRF51822 under SDK12.3. Here is the code lines of interest:
And here are the log messages:
iDrink:...
Good afternoon!
We're considering an off-the-shelf nRF52832 based device for our needs.
the application will likely involve two nRF5283-based devices fitted with external...
Dear All,
On the http_application_update after the download is complete, in order to run the new firmware the user needs to press the reset button.
I would like to be...
As in another post , I was looking for a way to change the TTL per message. Is there a reason that it can only be changed per model? I can imagine the TTL being part of the...
Hello,
I'm trying to use the mesh DFU on 2 nRF52840 DK by following the quick start guide and it didn't work.
Using the mesh sdk 2.0.1 I made the below batch file as described...
Hi,
We need a BLE chip which can be used as a radio which supports BLE SIG mesh and work on standard HCI commands.
Kindly suggest the right device.
Thanks & Regards...
I am using a Mac with SES installed. I created a DFU example and downloaded it to the Thingy 52 to see how it works. That all went fine. Unfortunately, it has disabled the...
Hi all, I'm trying to evaluate nRF Connect SDK, starting with guide in nRF Getting Started Assistant app. So far I've executed every step, but when I try to open the project...
We are using nRF52810 and SDK 15. We have to save up to 50 bonding information.nRF52180 is knowing to save up to 4 bonding information. Can you save up to 50 bonding information...
Hi,
we are trying to use FAT file in nRF9160. Referring the test case in "ncs\zephyr\tests\subsys\fs\multi-fs\src" to mount the FAT file.
But getting an error like "ff...
Hi I am migrating my application from SDK - 12.3 to SDK 15.3 version.
My application also uses FreeRTOS so I am referring to the ble_app_hrs_freertos example code.
I have...
