I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello,
I'm using this example of code (nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader\pca10040\dual_bank_ble_s132\arm5_no_packs) with my custom board to perform a dfu....
I have a peripheral device based on the nRF52832, using SDK 15.3.0. It uses a bunch of the standard services, including the TX Power Service, plus a custom one. When I connect...
What would be the best example to start with if i have to send the sensor data from nrf52840 to a mobile application using SDK for mesh? I have asked this question before...
Hi, could you tell me where I can find a sample project with button-less DFU-OTA and an application like ble_app_gls?
1. I use Windows 10; Embedded Studio; nRF52840 DK;...
Hello, We are using the NRF52840 and softdevice S140, PCA10056 on all examples. SDK version is 15.3. We see a problem following the secure OTA DFU protocol regarding acessing...
Hi,
I'm developing and testing the code using the PCA10040, but this board uses the NRF52382_XXAA which contains more memory and I want to use the NRF52382_XXAB. So, how...
Hello guys,
I have coin cell powered nRF52832 based sensor node. I develop the firmware in Segger Embedded Studio, SDK15.3.0.
On the pressure of a button on the sensor...
Mesh SDK:3.2.0
I want to send dimming level to server, and want return data of dimming level with mcu voltage.
When I receive server set callback, I tried: status publish...
I am developing a beacon-related project, my nrf51 device needs to play beacon. Beacon will determine the distance from NR51-> Smartphone. If distance = distance I give, I...
Hi all.
I am using a nrf52840 with mesh sdk 3.20 and sdk 15.30.
I am implementing RSSI tracking and require reference nodes to advertise once on each channel (37,38,39...
Hi guys,
I am using nordic semiconductor nrf52840 development board and segger. Is it possible to display the data of ultrasonic sensor on the nrf connect app by configuring...
Esteemed Colleagues,
We are using PCA10040 (1.2.4 2018.16) to develop a customized NFC Type 2 TAG. SDK 15.0.0 was used because we needed to work with hal_nfc_t2t.c instead...
Hi Team,
I am developing a low power application where we need to update Firmware frequently based on use cases.
I have successfully tested BLE secure DFU example and...
Hi,
We're trying to characterize the radio timings of the transmission of a Bluetooth Mesh packet from an originator in a Bluetooth Mesh network. Looking at the broadcast...
Hi,
In your nRF5 SDK v16.0.0 release note, I recognize that a new feature is added:
I am wondering which BLE event is indicating that SD has been free from BUSY state...
