Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi,
I am working on NRF52832 board in segger embedded studio. I am using nrf SDK 15.0.0.
I have created BLE custom characteristics and using nrfConnect mobile app to communicate...
Hi,
I am using nrf52840 Preview - DK, with SDK v15.3.0 and Softdevice API 6.1.1
I have modified the 'ble_app_blinky' example to have an advertising interval of 500ms...
Hello I am currently trying to combine BLE, SPI and TWI programs into one. I used SDK 15.0.0 and confirmed that each program works properly with keil. However, since keil...
Hi,
I meet a problem:
nrf52DK runs a rtos similar with nuttx. The debug environment is ubuntu 16.04; the debug log is printed via minicom.
When the JLinkExe is not opened...
Hi,
SDK 0.4.0 simple_mqtt project
Modem mfwnrf916007029alpha
I want to write an unique 4 bytes ID into each nRF9160 via nrfjprog.
So that, I can set subscription...
If the peripheral makes a connection with the central (the peripheral sends a packet, the central responds, and the peripheral sends a second packet) What is the calculation...
Hi and happy new year everyone,
I am a developer for Raytheon Anschütz GmbH in Kiel Germany and working on a Zigbee mesh sensor network. Unfortunately I am an absolute beginner...
Hi, radio experts here. Due to some limited conditions I have to implement one custom radio communication pattern in MCUBoot, not the BLE stack which is a bit too heavy for...
Hi.
I have some question.
I use Thingy52 module.
I want to use(merge) all service in Thingy:52 SDK v2.1.0 into Nordic-Thingy52-mesh-demo in Thing_bridge.
I'm trying...
Hi,
I have tested the following solution and it doesn't work if I try to load more bytes.
case BLE_EVENT_DATA_COUNT_HANDLES:
printf("BLE_EVENT_DATA_COUNT_HANDLES\n...
hi
I want to know where the gazell control the GPIO06, i connect a LED with this pin ,and its blinky when send data failed .
I used to see it controlled in somewhere but...
Hello,
in my design I used the antenna swra117d from Texas.
I am able to connect to my custom board with the nrf52 dongle and the nrf52 DK.
Unfortunately I can not connect...
I followed the recommended steps and got the at_client solution to build and flash in Segger Embedded Studio with tag "v0.4.0".
I installed it onto my board, and but didn...
Hi,
I'm currently programming a custom board using a nRF52832 ( using this wiring ). Everything was working great but I tried to play with SAADC and maybe did a wrong...
I am using the link below
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0/getting_started_softdevice.html#getting_started_sd
with 3 options...
