I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I am trying to send accelerometer values through bluetooth for nRF52832 and SDK 14.2. I am using "nrf-mpu-simple" program form this ' GitHub ' repository and added BLE...
Hi,
I use EasyDMA with UART.
I'm in permanent reception and the received octects go directly into a memory buffer.
When the buffer is full, the writing starts again...
I have been using a JTAG to program a nrf52832 chip (SD v15) during development and am now testing firmware updates from iOS. As part of it, I've made a firmware package using...
Hi,
the default board of the homekit SDK is PCA10040.
I want to run ble_hk_doorlock_static demo on board PCA10056 , What changes should I need to do?
tool-chain :...
I am currently trying to minimize radio noise when collecting data via the ADC, on a custom board powered by a battery (when the radio fires, it introduces a lot of noise...
Hi team,
My customer wants to apply Serial DFU in their product, but when they are developing with SDK13, they find our release notes with:
** DFU ** - Added support...
Hi I'm porting an existing project from nrf51 to nrf52810 and trying to configure the UARTE EasyDMA to handle serial reception.
We have serial messages of variable length...
Hi DevZone,
Is there an example implementation in SDK15 using Crypto-Frontend and Soft-Device together? I have been trying for days to merge two examples (tried to import...
Please tell me the setting range of the following parameters
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(20, UNIT_1_25_MS) /**< Minimum acceptable connection interval (20 ms...
Hi
I am running saadc battery measurement using the refernce code.
When I run the adc_configure() I have about 500uA consumption
then According to this thread I run...
Hi,
we are using BL600-SA in project,we want to configure ADC input Channel,In datasheet not able find the which channel number assigned to pins cleary,if we want to configure...
Hello everyone,
I'm facing difficulties trying to make SPI List work on the nRF52840. I'm using SPI1, clocked at 1M. START task is triggered via a GPIOTE event with PPI...
Hello,
I had a look at the brand new mesh 2.0 SDK, this looks very promising. I've been looking for some protocol description for the GATT connection to do the provisioning...
is there an expected release date for the soft device that supports the full bluetooth 5 specification including extended advertising beacons using a coded PHY with S=8(125...
When using nrf scanner to detect my beacon why BLE device name shown is 'N/A' , that field is designed for what? How can I change use ubuntu 'bluez' library? Thanks!
