I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Dear all members,
I am having a strange issue. I am using the iOS Nordic Toolbox and ble_app_uart. I am sending large amounts of data from Central to peripheral, iPhone...
Hi
I am working on migration to SDK 14.2. HOWEVER, I found softdevice_handler_appsh.h is missing.
May I ask is there any replacement function to the same thing, please...
I want to use the flash to store some values, I try to use the NVMC like the examples, but it cause the chip reboot. why it cause the chip reboot, and how can I fix it?
Hello everyone, I'm currently facing two problems :
1- I'm using nrf Toolbox with the last version and perform a DFU on a low_energy_ble device. I'm using a .zip and got...
Hi All:
I met a trouble， i don't slove it. i need help .
sdk : nRF5_SDK_14.0.0 S132
hardware: nrf52832
base multitole dev.
nrf52832 as master to connect mobile by ble...
hi everybody
SDK:14.2.0
CHIP:nrf52832AA
example: ble_app_uart or ble_app_beacon
board:my board,not DK
My board program into ble_app_uart or ble_app_beacon hex,it...
What's the maximum time between random numbers being generated on the nRF52832's RNG? The datasheet just says
The time needed to generate one random byte of data is...
Hello everyone,
I remember doing a project with PCA10028 board and S110 SDK a year or a year and a half ago. Now i want to do another project but all my materials which...
Hello,
I am writing this question in reference to this question . I was asked to be more specific about my question by my colegues. I do understand that this is a duplicate...
Hi,
I checked the flash_fds example. I could not tell the address it tries to access to. Is there any way I can find the address? Can I limited it to a certain address range...
According to this article, https://www.nordicsemi.com/eng/Products/Bluetooth-5, it appears that the nRF52 should be able to support standard BLE at 2Mb. However when I look...
Hi Nordic
I am using sdk 14.2.0 version and s332 soft device. Now I have completed the bicycle speed cadence code that works with ble_ant. It worked well as I wanted. But...
hi,
I am a fresher .I am asked to do the communication between nrf51 D K and moblie phone( nrf connect app). Can anyone provide me a sample code and required documents to...
