I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Do you have any ready made example where beacon and NRF52 DK are communicating will each other.
Our idea is that beacon sends data to the NRF52 DK and NRF52 DK sends the...
Sorry if this is obvious but I cannot find the units of nrf_esb_config_t::retransmit_delay
in the SDK documentation, it just says: "The delay between each retransmission...
Hej,
I'm working with the nRF24L01+ and the ATmega328p programmed in c. The goal is to have both TX and RX mode in the same device, mainly work as RX but in certain conditions...
Dear sirs, I've had a difficult time establishing communication between my nRF24L01+ board and the SPI bus on my Arduino Uno R3 microcontroller. Could you please provide me...
Hi all,
I am thinking of using a GPIO pin's "SENSE LOW" to wake up my device from SYSTEM OFF mode.
In order to avoid the device keeps waking up in case the pin stays low...
I am using an nrf51822 DK with a (so far) very simple code along:
main()
{
//... init I/O
run();
}
Inside run:
run()
{
uint32_t retval = NRF_SUCCESS;
...
Hey,
I recently got the nrf52 DK and tried to make use of the app_button library to have easy to use debouncing.
As far as I understood the library, the event should be...
Hi,
i have a problem withr the example "BLE ATT_MTU Throughput Example".
I flashed the soft devive with nRFgo Studios. Now I want to flash the example, but i got following...
I have want to make application where beacon sends data to NRF52 and NRF52 to PC.
But if for example, the connection between NRF52 and PC is through bluetooth instead to...
Hi,
I have bought a new nrf52840 PDK. I have gone through the PDK user guide and I came to know that we can use qspi pins as gpios by cutting the Solder bridge connections...
Hi All,
I am getting following error while compiling template example with DSP CMSIS library in IAR.
Fatal Error[Pe035]: #error directive: "Compiler generates FPU instructions...
Hello,
I have a question regarding AVDD(35/36) pin. I am using nRF51822 QFAA package. And the reference circuitry on the datasheet uses a 1.0nF capacitor between AVDD and...
Hi, my first post here.
I'm a undergraduate student and newcomer to this field. I've some programming background but few in electronics and embedded systems (so probably...
