Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Is there any way of instructing the BDS plug-in which optional characteristics to include in code generation for adopted services without converting to a custom service? ...
(/attachment/41972e0db37f912bba4731a3b5ffe839)(/attachment/0838bef738e72c89e2a9af90d6e3f640)(/attachment/a62ce68db8c9d23b285a9f94a5c9beac)I have been developing on the nRF51...
what should be the direction of pin P0.26 and P0.27 when external low frequency crystal is connected ???
or they should be left untouched in the code ???
To reduce the...
Hi:
I come across a problem when I debug NRF51822. I don't know how to config its clock.My board XTAL is 16MHz, and I want config is to 32MHz，Is the method below OK?
NRF_CLOCK...
Hi,
My settings are:
NRF_DRV_SPI_FREQ_1M, NRF_DRV_SPI_MODE_2, NRF_DRV_SPI_BIT_ORDER_MSB_FIRST.
I'm trying to readback 0xD8. The proper value should be 0x71. Instead...
Hi,
I am trying to use the nrf52 in serialized mode, where I was successfully able to program the connectivity board (using SDK 11.0.0) However if I try to load any of the...
We are using a module which has nrf51822 on it. Before we have programmed it, we were able to see it when we scan for ble.
But after we program we could not able to detect...
I am building an automated test stand for programming our production devices. After programming, I need to pin-reset the device to leave debug mode so I can get an accurate...
We have an BLE application that we are targeting the nRF52 device for. The application demands using a UART interface to communicate to a host processor. In addition, we typically...
Hi all,
until now, I used nRF51 Chips on my board. I programed them trough the nRF51DK(PCA10028). But now I would like to work with nRF52832 Chip. I have a nRF52DK(PCA10040...
hi ..
i am new to mbed and nrf51.
softdevice is s130
if i enable the ADC in my project then other output(out3,4,5,6) is not working ok.
if ADC is not enabled then...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi
I have a problem when bootloading with nrf toolbox. It seems like when i flash files over 0x10000 in size the program overwrites itself. When i flash files with smaller...
I know this is somewhat "how long is a piece of string". I'm happy for guidance rather than solid numbers:
I'm trying to spec a "keep alive" circuit for an nRF51822 project...
