I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I now this are basics. And I did this allready a few times, but in this project it simply wont work.
Maybe someone of you will find something, that is missing.
I`m working...
Examples like the "proximity application" are all associated with the nRF51422_xxAC. The part I'm using is the nRF51822_xxAA. How do I make this examples work with my part...
Hi,
I am wondering what to do to fix the error I have been getting while trying to debug my project. I am using app_trace for logging. I would often get an error on the...
I have a custom PCB with nRF51822. I have copied the "QFAA QFN48 with internal LDO setup" schematic from Product Specification v3.1. However, I have not copied the PCB layout...
Hello,
I am using a custom PCB with ISP130301 BLE module based on nRF51822. The PCB layout for the module is designed based on the recommended PCB land pattern and solder...
Hello,
yesterday i ordered th nrf52 Development Kit an just had a look in the Errata infocenter.nordicsemi.com/index.jsp So if i get my Development Board, will all this...
Hi,
I've read posts showing programming the Beacon with nRF51-DK using the debug-out port. As the nRF52-DK is available right now, does anyone have any idea if I can use...
I'm using SDK 7.1, PCA10028 eval board, SD310 2.0.1, MCP 3.8.0.7
I need to check if notifications have been enabled by the central - if they have I then want to notify...
I wanted to test nrf51-ble-driver_linux_0.5.0 in the latest Ubuntu, but got this problem:
...
OSError: libboost_thread.so.1.54.0: cannot open shared object file: No such...
Is this even possible? I have a BLE connection with an interval of 7.5 ms. I've set up a radio notification with a distance of 2680us in order to be able to transmit 4 BLE...
Hi,
I want to know how sd_ble_gap_authenticate api works.After executing this api, what are the events invoked at peripheral end. Is there any event that blocks CPU or...
We are designing product based on nrf2401A
The problem that we encountered was that the nrf2401A forgeted configuration data, was it possible ?
we use our product in highly...
Hi,
I am using the nrf51822 in an intermittent high-current application where if the battery is close to dead, will sometimes cause the chip to reset because the voltage...
