I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hello, I read an article on Nordic site about the Blend Micro:
*"The Blend and Blend Micro also natively support (with no extra wiring) all Nordic Semiconductor nRF8001...
Hi,
I have a few questions on how to receive data (from an iPhone app) as a a peripheral device on nrf8001 (with RedBearLab BLE shield).
Basically I am trying to receive...
Hi,
how do you use the jlink gdb server?
All i get is Target halted (PC = 0xFFFFFFFE),
gdb will obviously not show any helpful trace for that and continue doesn't work...
Dear Nordic guy,
I 'm developing LG product with nrf51822 chip.
I have some question.
Applcation SW timer use the rtc1 clock source.so,
When NRF_timer interrupt expired...
Hi, I'm attempting to use API 2.1.3 and am experiencing some weird issues with transmission intervals. When I use UpdateConnectionParameters to set a connection interval of...
Hi,
I want to upload a firmware using DFU mode.
If I use toolbox 1.8 app of android I can upload the new firm, but If I use toolbox on my iphone, when I push upload the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Dear Sir,
In SDK5.2.0 S310 HRM example, one nRF51422 act as BLE and ANT RX character.
Another nRF51422 with S210 software act as ANT TX character to send out command...
Hello all,
I want to do current measurement for nrf51822 which is flashed with my own ble application which uses some custom services. As mentioned in evaluation kit user...
Hello,
My team and I are trying to decide how to power the nrf51822. We will be using a 3.7V lithium ion battery as our power source.
I saw in another post that it is...
I am planning to use the LPCOMP in conjunction with an external reference. I would like to just use a voltage divider to create the external reference.
Are there any impedance...
I recently received a nrf51822 mbed board.
I went with the mbed board over the EK because I figured it was more 'open', without realizing exactly what mbed was. I played...
I use the SPI slave function on 51422. When I send a byte(0x31) to 51422 SPI slave from master, 51422 will back a byte (0xAA - DEF byte) to master. Why?
I send 0x31 every...
