I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I am new to this forum, and can be described as a programmer with very little embedded experience.
I have bought a nRF51822 BT SMART BEACON KIT, and are trying to...
Hello,
i would like to turn off a sensor completely when unused and thought of powering it through the GPIO of the Controller.
I wondered if it is recommended or do the...
We have updated multiple android phones to nRF Toolbox for BLE app and we are all getting "Unfortunately, nRF Toolbox has stopped." error message when opening the app. nRF...
Hi,
I want to get a notification when the BLE event is started, in order to start a timer just after.
How can I get that?
I want to clarify my question :
My board...
I use the NRF 24AP2E in my communications, and I need detect if the communication is good.
I active the RSSI message, but in scanning mode I don't receive byte 0x20 in Measurement...
Hi All,
I am designing a circuit with nrf51822 and mcp25625 (microchip spi can interface). mcp25625 has an internal 16mHz xtal clock circuit and a digital clock out, I...
Hi, i'm kinda a newbie on this, and i'm trying to port the SDK available for arduino to a PIC, i followed the instructions on the SDK and also here
Now i want to verify...
I ran into an issue recently of attempting to make a pstorage_update call from the callback set in pstorage_register . It resulted in a difficult to track down error, so I...
I have a USB dongle of nRF24LU1p and it is identified as the Basic Remote firmware with a VID:PID of 1519:002B. I would like to reprogram it over USB but do not know how to...
For nRF 51822 radio transmission, the payload packet is started at the NRF_RADIO->PACKETPTR. Then what is the packet size? is there any parameters to control the packet size...
I should have an own function wich is called upon after Port 3 goes low. I haven't succeeded yet using ppi channels. (I'm using the NRF51422)
For the moment the code is...
Hello folks ;
I'm new here and glad to have such kind people around to see helping those other developers ..
Here is my question
I'm using one of the NRF24L01 modules...
Hi,
I'm using the attached circuit and we recently took our product to FCC testing and failed the 2nd harmonic because we were transmitting too much power.
I'd like...
Hi All,
We have been working on Arduino Mega board with BLE shield. We want to get the address of the BLE shield and we are using aci library for that.
I found this...
