Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
I saw a description about on-the-fly CCM mode decryption in the nRF54L10 datasheet, but the Configuration section of CCM00 states that it does not support on-the-fly decryption...
I would like to know about the Mesh model.
Light Lightness、
Light CTL、
Light HSL Setup、
Light Control
Are there no configuration components for any of the above...
Hey,
To program the nRF54L15 EVK, is there some dedicated program tool needed?
From EVK package ordered online, there is only USB cable inside. Can I assume the USB cable...
SDK: 3.0, nRF54L15
I have modified the clusters using ZAP tool (west zap-gui). When I tried to built, I get the below error:
1. I used Matter door lock sample and the...
Hi I am starting with nRF9160. I build and program "nrf91_simple_tracker," but while running, I got the following terminal output:
I am using nRF Connect SDK v2.7.0 with...
I'm developing a solution using nrF54L15 that needs to receive packets from existing legacy RF devices in the field that cannot be modified.
Required RF Parameters:
...
Hi team,
I am using ncs2.6.1 ( github - install from VS Code ) , toolchain 3.0.2 ( previously used 2.6.1), My DK works great standalone also here is the view from nrf-connect...
Hi,
I am planning to get the PPK2 fabricated and assembled using the HW files available for PPK2.
Just wanted to check will I have issues loading FW on it since I don...
Hi all,
I’m working with an nRF52833 using SDK 2.8 and trying to enable DCDC mode to reduce current consumption.
I tried adding:
CONFIG_BOARD_ENABLE_DCDC=y but I got...
When developing a keyboard peripheral using the nRF5 SDK keyboard example, how can I determine whether the connected host device is a Mac, Windows PC, or Android phone?（NRF52833...
Hi, I am working on a channel sounding trilateration system using an initiator and three reflectors. When I was testing with six reflectors I couldn't help but notice the...
Hi all,
I need to use the SPI3M interface and following various example I implemented the following code on the nRF52840 with SDK 3.0.2
Whenever I configure the SPI to...
Hello - Just download and installed NRF Connect for Desktop 5.2.0 on Windows 10. Trying to Quick Connect to new PPK2 1.1.1.
When I plug in USB Quick Connect sees the PPK...
Hello,
we were using the mcumr_flutter 0.4.2 library to Update our NRF54L10 over the air with an app. This was working fine using the nRF Connect SDK Toolchain v2.9.0. However...
Hello,
I'd like to have the gcc linker calculate a checksum over a specific address range (defined in .ld file) and store that checksum at a specific address (defined...
