Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I'm trying to run Provisioner Example on my nrf52840 DK, which is in examples/provisioner directory, . First I've build softdevice on DK and then I'm trying to build provisioner...
Hey NordicSemi. In my new project, I use DK NRF9160 and I need to determine the location. Since hardware GPS does not work, I decided to use the detection of coordinates through...
Hi,
Something locks-up my I2C sometimes and I need to make I2C recovery. It looks like Nordic has not implemented the zephyr i2c_recover_bus function, so I guess I need...
I'm looking for dual core inter task communication examples
where a thread on one core is interacting with a thread on the other core ?
e.g. will there be some kind of...
Hello All,
I was looking at the Digi XBee3 modules for a ZigBee project I am working on. What is great is they allow you to write MicroPython code to control the network...
I am trying to send some values from nRF52810 Board to my Laptop. I am using a nRF52840 Bluetooth Dongle to connect the board to my laptop. I am using the "Heart Rate Collector...
Is there a way to get the values of CompanyID ProductID & VersionID before provisioning? I'm working on my android application using the nRF Mesh Library and after identification...
Hello, I work on nrf9160 dk and i try to get tx power: For exemple, with a RSRP -76 dbm i get this consommation curve (read current on P24 throught 0.5ohms resistor):
and...
Hello,
we are developing a HID slave device. we need to support five cell phones connect and bond with the device not at the same time.
we use the ble_hid_keyboard example...
Hi,
I am check this code: https://github.com/NistantriTech/ibeacon_nrf52/tree/ed938973c9a8ebd4f0bb91a3689e5d8242980681
It used SDK15.0
On Ebyte 52832 - and face problems...
Hi
After trying out nRF5340 step-by-step guide we'd like to learn nRF52833 following similar step-by-step start-up guidance if such exists.
I guess for the basic operation...
Hi all. I am using the twi_sensor example of the sdk12.3 in a NRF51822 Taking a look on the tx function: err_code = nrf_drv_twi_tx(&m_twi, MXC400_ADDR, reg, sizeof(reg), false...
Hello ,
we know that, when initialize a BLE slave device ,we need to define the BLE MAC address type.(we need to write our owen address ,not usig the original ble address...
