Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
we are using the nrf9160 for our fleet management products, and am currently working on downloading firmware updates from our server. I am using an HTTPS POST request...
Hi,
I am running an RTC unit test on the boards (nRF52840), where I take RTC_Val1 then perform a delay for one second then take another RTC_val2.
My condition for passing...
Hi,
I am very green with Nordic's tool chain, so this is probably my fault.
I used the toolchain manager to download v1.3.1 and it worked fine, but I can't follow first...
Hi,
Recently, I was researching about BLE Serialization for an upcoming training project. I want to get to know about the following points (some reading material, tips or...
Hi,
I have 10 custom boards with the nRF52840 chip.
9 boards of them perform the DFU successfully.
And just one board fails with it, All the boards have the same bootloader...
Hi.
I'm having an issue with the libuarte library. It seems to work perfectly but after some hours of running the program crashes because nrf_balloc_alloc returns NULL inside...
Hello,
I was trying to open SEGGER Embedded Studio for ARM V4.20a on MAC.
However, I encountered:
"SEGGER Embedded Studio configuration error. 'studio.xml' user interface...
Hi,
Last December I started to know about NORDIC nRF5340. I thought it could be a very good SoC for developing our next BLE wireless product. Considering the huge number...
I programmed my thingy91 with lte_ble_gateway example, however I want to be able to connect to devices with specific addresses. Can anyone point me in the right direction...
Hi,
I am using pwm driver to generate different square wave of different frequencies in order to drive a buzzer to play melody.
Below is how I init my pwm software module...
I have the following problem:
1 to 3 phones are bonded with an nRF52832
These phones are on the whitelist of nRF52832
nRF52832 goes into Power Off Mode
nRF52832...
Hi,
We are integrating the nRF52840 into a new test apparatus and I am using the nRF52840-DK for development. I have pulled out my unit from storage and it will not power...
Hi,
There was an app timer immediate expiration issue with my project which is using nrf52840 + S DK 15.3.0 on custom board.
So I changed apptimer code to app timer2...
I was wondering why the RSSI Viewer Values are locked to a minimum of -33 dBm. Is there any reason for that and is there a workaround to get lower values? Currently I am using...