I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
IMEI 352656100982084
I need your support to solve this matter urgently because we are developing a IOT solution to monitor several thousand motors - one Thingy 91 for each...
Hi Team,
We are using nRF9160 -DK (0.8.3), As per the document we followed the procedure from here . Loaded the respective application to the on board controller(nRF52840...
Hello
I try to use nrf24l01 in multiceiver mode for a domestic application
I made a simple set-up with 2 nrf24l. On the receiver i activated 4 pipes (0 to 3) with these...
Hi,
I have updated the modem to version 1.2, and connect sdk to 1.2, and now the SUPL library doesn't work? I'm using the GPS sample and it is getting stuck at "starting...
I have the mesh light switch on/off example running. What is the easiest way to test sending and receiving data from a non-mesh device to the proxy node? I want to be able...
Hi All,
I have programmed my nrf52832 device with DFU bootloader,softdevice and buttonless app provided by SDK. I am using SDK16.
My device is getting recognized by nRFConnect...
Hi:
The nRF52840 VDD voltage supply range is 1.7~3.6V
So if we provide 3.3V to VDD, the voltage ripple spec. is still 1.7~3.6V?
Or other spec. that we need follow? ...
Hi,
I am evaluating a BLE beacon solution and the nRF52 seems attractive. If building a solution where an appliance I will develop will listen for a BLE beacon that I also...
Hello,
I am new on keil and nrf, I am trying to merge nrf52832 sdk15.0 ble_app_hrs example and this custom service
I want to send command from nrf connect app to my nrf52832...
Hello,
I am working on a BLE application for the Thingy91 which needs a lot of dynamic memory. In the Zephyr specification values of up to 16kB are supported. I tried to...
I am using zigbee light_control examples in nRF5_SDK_for_Thread_and_Zigbee_v4.0.0 for my zigbee projection.I want to know how the zigbee network build and which command will...
Hello, I have been using segger embedded studio v4.16 for almost one year using free license. today it says my evaluation period is expired. But they say it is for unlimited...
I have a setup with one transmitter and three receivers. The transmitter (nRF24L01+) sends a message to the receivers (nRF52832, using SDK v15.3.0) every 10 seconds. The receivers...
Setup: Segger Embedded Studio v3.52, nRF5_SDK_for_Thread_and_Zigbee_v4, nRF52840 Custom Board
Hello,
I based my code off of your Zigbee cli_agent_router example. In the...
