I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi there
Does anybody now if there is a implementation / reference project / company which solves the firmware over the air update of several devices inside a OpenThread...
I am having nrf52833 module where I need to update the firmware via uart, I am using sdk_16 and I'm unable to find the PCA10010 for uart. Can anyone suggest me how to attempt...
Hello,
I am currently developing a project using the nRF 9151 and SDK version v2.7.0.
The issue I am facing is that I have configured the PSM mode, but it doesn't seem...
SDK v2.7.0 nRF5340-DK with nRF7002-EK Matter samples (e.g. light bulb) Extra CMake arguments: -DSHIELD=nrf7002ek Use sysbuild
Tested with v2.6.2 (no sysbuild), and it...
hello ,
some brief about my board it is nrf ble nrf52810 without crystal.
i am using segger debugger.
while doing step by step execution it come till line sd_softdevice_enable...
Hello！
I am using the development board of NRF5340DK, I found an external flash (MX25) on it, I want to know how to program the external flash through the onboard jlink...
Hi, our design makes use of nRF52840 MCU. Power is supplied to VDDH pin from a Li-Po battery which can range from 2.5V to 4.2V. Internal REG0 is used to regulate voltage down...
Hello I want to add an extra config file based on the option in prj.conf or in Kconfg. For example: CONFIG_WIFI_SCAN_ONLY=y include the overlay-nrf7000-wifi-scan-only.conf...
Hello,
When I upload the Matter Weather Station application to my Nordic Thingy:53, I encounter a problem.
I am trying to use Google Home to read sensor data, such as...
Hello, I have a custom development board using the 52840 chip, with two LEDs and a serial port connected. It worked well when developing with nrf5 previously. Recently, when...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
While compiling the custom project in nrf vs code , I am getting the following error;
Configuring incomplete...
Hi,
1. As shown in the following figure, how to resolve such a default instance compilation error?
2. I have used west update to confirm that ncs v2.9.0-rc1 is successful...
Hi,
I have a nRF24L01+ as the TX and have lots of existing nRF24L01+ RXs. I would like use the nRF52810 as the RX as it saves the need for an MCU and on BOM parts. The current...
The text for the recommended nRF Connect SDK workflow (using a Workspace Application Repository - https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/dev_model_and_contributions...
