Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hello,
I am attempting to use the DFU Target library to receive an update file over a custom protocol. I aim to do an MCUboot-style upgrade such that after the file upload...
Hi there,
My compiled image size in ROM is ~200kb.
I have 2 MCUboot partiitons, each 228kB.
I wanted to ask- is it possible for the application to use the second (non...
NCS v2.7.0
nRF52840 dongle
I want to program the nRF52840 dongle with external J-Link, and I can connect to nRF52840 dongle with SWD now. Using "nRF52840 Dongle nRF52840...
Hi,
I am evaluation PAWR feature and plan to use it for a product. The project is based on nrf5340.My enviroment is:
nrfconnect sdk v2.7.0
nrf5340 audio dk.
After...
Need to automate the FOTA process for devices with Zephyr build application which has mcuboot as bootloader, these devices can be programmed using nRF Device Manager and nRF...
I’m developing a product that uses the nRF9160 for LTE-M and the nRF52840 for Bluetooth. The nRF52840 is a pre-certified module, and I have experience with FCC compliance...
Is there any hardware limitations that would prevent one from using the nrf_802154 drivers on an nRF9161? If no, could you adapt the open-source sl to use the 9161 modem instead...
Setup: custom nrf9161 PCB, flashed with nrf9161 modem fw 2.0.1, using NCS 2.6.1
Targeting my custom board, I couldn't even speak to the modem lib, no IMEI etc.
So I dug...
Hello,
I have been trying to correctly setup my nRF Connect inside VS Code.
When I try to execute the command
west -V
in a nRF Connect window inside VS Code, I...
Hi i am using nRF52840 with segger embedded studio.
SDK -> nrf5-sdk 17.1.0 I want to configure rtc2 so that whenver i initialize it it should generate an interrupt after...
Hello, I am building a device which simultaneously advertises as a beacon and acts as a peripheral role device. Advertisements are sent at ~20 Hz with the connection to the...
hi:
I am use broadcast_sink and broadcast_source of nrf5340_audio simultaneously. use a button to switch source or sink. i am use NCS v2.6.2 if switch to sink mode is show...
Hello friends, I am using nrf52833 MCU for my current project, this project involves a sensor from infineon that operate on SPI and it supports high frequencies up to 50 MHz...
Hi,
I referred to the DevAcademy FOTA over Bluetooth Low Energy, but in the provided code, the BLE mobile app connects to the device and it automatically enters DFU mode...
on cannot connect to the on-board Jink of the NRF52840DK board
I have tried:
Updating to the latest Jink driver
installed nrf connect tools for windows
connecting...
