After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
Hello, I am building a power switch for my application and have some questions about expected behavior when holding a GPIO output signal at HIGH during System ON sleep mode...
Hello, I tried to merged two examples from SDK
1) I run ble_app_bps example from SDK 15.0 HW - PCA10056, nRF52840
2) I included to the main.c
3) I defined in sdk_condif...
Hello,
I am working on a little app running on nrf5340 app core. Now I want also to program the network core, to be able to exchange data via shared memory as little demo...
IMEI 352656100982084
I need your support to solve this matter urgently because we are developing a IOT solution to monitor several thousand motors - one Thingy 91 for each...
Hi Team,
We are using nRF9160 -DK (0.8.3), As per the document we followed the procedure from here . Loaded the respective application to the on board controller(nRF52840...
Hello
I try to use nrf24l01 in multiceiver mode for a domestic application
I made a simple set-up with 2 nrf24l. On the receiver i activated 4 pipes (0 to 3) with these...
Hi,
I have updated the modem to version 1.2, and connect sdk to 1.2, and now the SUPL library doesn't work? I'm using the GPS sample and it is getting stuck at "starting...
I have the mesh light switch on/off example running. What is the easiest way to test sending and receiving data from a non-mesh device to the proxy node? I want to be able...
Hi All,
I have programmed my nrf52832 device with DFU bootloader,softdevice and buttonless app provided by SDK. I am using SDK16.
My device is getting recognized by nRFConnect...
Hi:
The nRF52840 VDD voltage supply range is 1.7~3.6V
So if we provide 3.3V to VDD, the voltage ripple spec. is still 1.7~3.6V?
Or other spec. that we need follow? ...
Hi,
I am evaluating a BLE beacon solution and the nRF52 seems attractive. If building a solution where an appliance I will develop will listen for a BLE beacon that I also...
Hello,
I am new on keil and nrf, I am trying to merge nrf52832 sdk15.0 ble_app_hrs example and this custom service
I want to send command from nrf connect app to my nrf52832...
Hello,
I am working on a BLE application for the Thingy91 which needs a lot of dynamic memory. In the Zephyr specification values of up to 16kB are supported. I tried to...
