Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
The ble-sniffer_win_1.2_user_guide, Figure 4. Wireshark Interface, Packet Bytes window shows a 00 byte at location 0010, which corresponds to the "preamble" of the "Air Interface...
Hi
I want to declare 2 spi instances with only cs pin different.
The reason for dividing the two is because the modes are different.
The one declared above is executed...
I have used nRF5 SDK ver.16 for BLE HID digtiger.
I want to set up some feature value to HID report . Such as Contact count maximum.
I have followed keyboard example,...
I turned off the serial i n prj.conf of the mqtt_simple routine.
<prj.conf>
<nrf9160dk_nrf9160ns.overlay>
The idle current was measured at 500UA. This means that...
Hello Engineers,
We are trying to set the correct configuration between nrf9160 and nrf52840 for using the uart_pipe library. However we are still unable to communicate...
We have a Nordic development under way and I have run into a snag.
Neither of my dk board types (9160 or 52840) are recognized by jlink , no jlink drive etc….
I have personally...
So the interrupt on the nRF2401+ seems to be working inconsistently. I get interrupts sometimes and sometimes I don't.
For a context: I'm transmitting a sensor data only...
Hi, we recently purchased a Nordic Thingy 52 module and were trying to program it. We used a J-link recorder and a cable for the connection between the J-link and the Thingy...
Hi all,
I am using the nRF51822 and attach you can find the . .
I have noted that the current consumption is too hight for my scope (about 1.7mA). My idea is to 'reduce...
I tried: - changing USB cables and ports (no any improvement)
- instructions from this link devzone.nordicsemi.com/.../nrf52-dk-does-not-show-as-a-removeable-drive-in-windows...
Hi there,
My question is similar to https://devzone.nordicsemi.com/f/nordic-q-a/39447/central-role-in-a-mesh-proxy-node , but perhaps slightly different in that my existing...
DFU Trigger Library (USB) is indicated that only for nRF52840 SoC. For other SoCs, can I use it after some modification of the library easily? What's the limits?
Hi !
I am on a firmware project for a nrf52832. I am using SES on Windows.
There seem to be a problem when combining buttonless DFU and NUS. When I do the services_init...
Dear devzone community,
I am currently in the process of migrating my MBED code to NRF5 SDK. My MBED code is functional and it works fine, you can find the code below: ...
There is no any Softdevice S122 listed on the page below.
https://www.nordicsemi.com/Software-and-tools/Software/nRF5-SDK
We have downloaded the SDK from the same page...
