Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hello,
After searching in forum, I understood that we cannot debug application with softdevice unless PRIMASK bit is set.
But in my application there is a requirement...
Hi Nordic
I am using GZLL to develop a prototype whereby data from sensors will be transferred to a Computer in a Wireless sensor network.
The idea is, when data are requested...
Dear all,
we want to use a nRF52837 for a developement project we are planning. We have been asking ourselves on which functional level the alpha Softdevice S132 for the...
Hello, i analyze the device manager routine (device_manager_peripheral.c) and in BLE_GAP_EVT_CONNECTED case you checking containing the device address in bonded table.
My...
I am working with nRF51822 beacons and an iOS 9 application that I am developing. I am testing on an iPhone 6. My application uses the CLLocationManager's beacon ranging functionality...
Hi,
I want to use the whole payload of the advertising packet. I decided to use the manufacturer specific data. BUt I cant´use the whole payload by myself. I get this payload...
dear all：
I use the spi slave mode. i have a question,pls help me.thanks.the questions as follow:
I want to distinguish instruction type, and then reply to the corresponding...
Hello,
I am working on nrf51822 SDK 9.0 and softdevice 8.0 . I got the application note to create a custom profile for SDK 5.2.0 and softdevice 6.0.0 in nAN-36_v1.1 . ...
Hi: We develop our program based on (nrf51822 QFAAG0 1403AL), I found a serious problem that our new IC is (nrf51822 QFAAG2 1415AF), and the old program can't run on it any...
Not sure where to post this...
but there's a minor bug in components/toolchain/system_nrf52.c, where NRF_UICR->PSELRESET[0] is being checked twice to see if a reset pin...
While ota dfu via nrf toolbox android app, it sends wrong (0x15918) image size in start packet, and also bootloader starts writing softdevice image at address DFU_BANK_0_REGION_START...
Hi! I want to make a BLE network with 1 master (nRF51-DK) and multiples slaves (nRF51-dongle). I`ll send differents commands from master to slaves. This is for home automation...
Hello,
I am writing an application using SDK version 8.1 where I have a pin using the PORT event in nrf_drv_gpiote library. I have a need to disable the event temporarily...
I am encountering a problem with GPIOTE PORT events on the NRF51422 in a custom design. The chip occasionally seems to be able to get into a state in which the registers are...
